RF Gain Factory Defaults

[Malcolm Rothwell]

After seeing various posts on this subject, thought I'd give it a try. Unfortunately when I opt for factory defaults and click on "Calibrate" I get the following error message : E0400E3 ERR DSE on the K3 display and on the K3 utility I see "DSP command response did not arrive". The radio is performing normally, should I panic??

73 Mal G4KFT

[Ken Wagner K3IU]

Mal:
I've had a similar problem when using the XG1 to run the RF
Calibration on the SUB Rx (Main works fine). Dick
Dievendorff (author of K3 Utility) is aware of the problem
and will hand it off to Lyle when he gets back from vacation
shortly.
73,
Ken K3IU

On 10/21/2010 7:08 AM, Malcolm Rothwell wrote:
> After seeing various posts on this subject, thought I'd give it a try.
> Unfortunately when I opt for factory defaults and click on "Calibrate" I get
> the following error message : E0400E3 ERR DSE on the K3 display and on the
> K3 utility I see "DSP command response did not arrive". The radio is
> performing normally, should I panic??
>
> 73 Mal G4KFT
>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[M0XDF]

Don't panic!
check you've installed the latest F/W and you have installed all files (all checkboxes in K3 Util for files checked).

If it's not installing correctly, double check the baud speed on both K3 and Util.
73 de M0XDF, K3 #174, P3 #108
--
Hofstadter's Law: The time and effort required to complete a project are
always more than you expect, even when you take into account Hofstadter's
Law.

On 21 Oct 2010, at 12:08, Malcolm Rothwell wrote:

>
> After seeing various posts on this subject, thought I'd give it a try.
> Unfortunately when I opt for factory defaults and click on "Calibrate" I get
> the following error message : E0400E3 ERR DSE on the K3 display and on the
> K3 utility I see "DSP command response did not arrive". The radio is
> performing normally, should I panic??
>
> 73 Mal G4KFT
>
> --
> View this message in context: http://elecraft.365791.n2.nabble.com/RF-Gain-Factory-Defaults-tp5658229p5658229.html
> Sent from the Elecraft mailing list archive at Nabble.com.
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[GM4KGK]

Malcolm
This issue has been resolved with the latest version of the K3 Utility (1.3.10.11).
Your firmware is probably OK, but it will do no harm to re-load it before you run the Calibration procedure.
73
Norman - GM4KGK

Malcolm Rothwell wrote

Unfortunately when I opt for factory defaults and click on "Calibrate" I get the following error message : E0400E3 ERR DSE on the K3 display and on the K3 utility I see "DSP command response did not arrive".