Re: ANTENNAE LINE THROUGH WALL INTALLATION

[k3yt-2]

Hi Bill,

When we moved into our house 11 years ago
I put a feed through in the concrete block wall.

I used 2 inch PVC.  I drew out the size of the
circle I needed and cut out the drywall.  Make sure
that there are not any 110v lines where you want
 to put the feed through.  Also try to place it so you
are going through a hollow spot on the block.   Then I
drilled a series of small holes
on the circumference.  Then I just hit it with  
a hammer and knocked it out.   Same for the outside.

I got some stucco patch at Home Depot and patched around
the PVC on the outside.  I finished it by putting a 90 degree fitting on as
a weatherhead.

Don't fill it with expanding foam...you'll regret it.  A small piece of
fiberglas insulation will keep out wind and critters.

Anyway that is what I did....the cheap way and still is fine.

Went throught Frances, Jeanne and Wilma.

73 de Bob K3YT
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Sam Morgan-2]

[hidden email] wrote:

>
> Hi Bill,
>
> When we moved into our house 11 years ago
> I put a feed through in the concrete block wall.
>
> I used 2 inch PVC.  I drew out the size of the
> circle I needed and cut out the drywall.  Make sure
> that there are not any 110v lines where you want
>  to put the feed through.  Also try to place it so you
> are going through a hollow spot on the block.   Then I
> drilled a series of small holes
> on the circumference.  Then I just hit it with  
> a hammer and knocked it out.   Same for the outside.
>
> I got some stucco patch at Home Depot and patched around
> the PVC on the outside.  I finished it by putting a 90 degree fitting on as
> a weatherhead.
>
> Don't fill it with expanding foam...you'll regret it.  A small piece of
> fiberglas insulation will keep out wind and critters.
>
> Anyway that is what I did....the cheap way and still is fine.
>

I did much the same, with one added feature. I didn't trust the drip loops and
driving West Texas rains, (when we do finally get rain), so I made the drill
through at a slight downward angle to the outside. I know, after you seal it, it
shouldn't matter. I used some DAP I had from a bathroom project for the seal,
easily removable, (the landlord allowed a 2nd antenna later). Guess it was like
chicken soup, made me feel better. :-)
--
GB & 73's
KA5OAI
Sam Morgan
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Ron D'Eau Claire-2]

It may sound like overkill to drill at a downward angle toward the outside
in most installations, but it's an excellent idea in addition to a good drip
loop, especially for frame houses that have walls made of wood and other
organic materials. Even a small amount of moisture from snow building up
right on the fitting where it exits the wall or the small amount of rain
that will contact it directly can seep inside and start dry rot and other
problems.

Here in the northwest mold is a real concern. It's not just a nuisance, but
a life-threatening concern that has killed people, especially children, who
are unlucky enough to breath the air containing the spores. A couple of
years ago a builder left some tiny gaps in wood siding on a new home that
allowed moisture to seep in. Deadly black mold to started growing. Once
started it spread drawing moisture from the air. By the time it was
discovered because the family was suffering health problems, a new, 1.5
million dollar home had to be totally demolished and much of it disposed of
as toxic waste, complete with the crews working in bunny suits inside a tent
loading the remains of the house into sealed bags.

When you're running open wire feeders or a single end-fed wire, good
electrical insulation is important too unless the power is very low. Heyes,
in his book "Practical Wire Antennas" tells a story about visiting a fellow
Ham in England who used an end-fed wire that came into the shack through a
small hole drilled in the wood frame of a window. On one band a voltage loop
occurred at that point. Whenever the guy transmitted, smoke would curl up
out of the hole where the wire touched the wood. Heyes observed that he was
not aware that the Fire Brigade ever had to visit, but it didn't seem like a
good way to get the RF outside <G>.

Ron AC7AC



-----Original Message-----
I did much the same, with one added feature. I didn't trust the drip loops
and
driving West Texas rains, (when we do finally get rain), so I made the drill

through at a slight downward angle to the outside. I know, after you seal
it, it
shouldn't matter. I used some DAP I had from a bathroom project for the
seal,
easily removable, (the landlord allowed a 2nd antenna later). Guess it was
like
chicken soup, made me feel better. :-)
--
GB & 73's
KA5OAI
Sam Morgan

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com