Re: Audio direct

[Wes Stewart-2]

So?

On 4/20/2016 10:22 AM, Nr4c wrote:
> This is not AGSK A mode. It is FSK D.
>
> Sent from my iPhone
> ...nr4c. bill
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Mike Dodd]

I just upgraded from a KX3/PX3 to a K3s/P3. On my PX3, I could hold a
key (LABELS?) to get a two-line display of characters the KX3 decoded in
CW and data modes.

I can't find this feature on my P3. Is it there? The only place the
owner's manual mentions text decode is in the SVGA section. I do not
have the SVGA option.

How do I make the P3 display decoded text?

Thanks.

--
73, Mike N4CF
Louisa County, VA USA
Elecraft K3s/100
Carolina Windom up 45'
http://n4cf.mdodd.com
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Cady, Fred-2]

Hi Mike,
You have to have the SVGA option in the P3 to be able to display decoded text.
73,
Fred KE7X

For all KE7X  Elecraft books, see www.ke7x.com


________________________________________
From: Elecraft <[hidden email]> on behalf of Mike Dodd <[hidden email]>
Sent: Wednesday, April 20, 2016 9:01 PM
To: [hidden email]
Subject: [Elecraft] P3 CW/data text decode?

I just upgraded from a KX3/PX3 to a K3s/P3. On my PX3, I could hold a
key (LABELS?) to get a two-line display of characters the KX3 decoded in
CW and data modes.

I can't find this feature on my P3. Is it there? The only place the
owner's manual mentions text decode is in the SVGA section. I do not
have the SVGA option.

How do I make the P3 display decoded text?

Thanks.

--
73, Mike N4CF
Louisa County, VA USA
Elecraft K3s/100
Carolina Windom up 45'
http://n4cf.mdodd.com
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[KC6CNN]

CONTENTS DELETED

The author has deleted this message.

[KC6CNN]

CONTENTS DELETED

The author has deleted this message.

[Mike Dodd]

On 4/20/2016 2:29 PM, Gary Smith wrote:
> Now I have the K3s set to use AFSK A so
> that I don't need to have additional
> hardware/connections and no longer use the
> paddles to send, only MMTTY.
>
> When I use MMTTY I have to have  the
> PTT-KEY set to OFF-OFF. When I switch to
> N1MM I have to have it set to DTR-RTS.

I'm new at RTTY myself, but I have it working with MMTTY, N1MM+, and the
K3s built-in sound card.

With MMTTY, all I need to do is hold the VOX button to turn on VOX. I
set MMTTY's oundcard output level to maximum, the K3s MIC to 2, and the
VOX GAIN to 10. When I click the TX button in MMTTY, my K3s keys and
sends RTTY (hold TEST to put the K3 in test mode with no RF output).

For N1MM+, all I need to do is hold the VOX button to switch back to
PTT, and I'm good to go. No DTR-RTS is needed.

Do not try to run stand-along MMTTY with N1MM+. Exit MMTTY. N1MM+
launches the MMTTY engine when you open a digital window. You _must_
read the N1MM+ docs to figure out how to set up N1MM+ with MMTTY.

I have attached a screen shot showing the deeply hidden check box to use
PTT with N1MM+. If the attachment doesn't come through, email me
off-list, and I'll send it to you directly.

Bottom line for me is: Select DATA -> AFSK-A, turn on VOX, launch MMTTY,
and I'm on the air with RTTY. For contests, launch N1MM+, turn off VOX,
and I'm on the air with RTTY. No sweat.

But I did have to read the N1MM+ docs to set it up to use the MMTTY engine.

--
73, Mike N4CF
Louisa County, VA USA
Elecraft K3s/100
Carolina Windom up 45'
http://n4cf.mdodd.com

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Mike Dodd]

After being disappointed by the P3's inability to display decode CW and
data text (as the PX3 does) without the SVGA option (that's definitely
the BOO of the week!), I am now searching for a tiny monitor that won't
wipe out half my remaining desk space.

I have a couple of questions:

1. I found some 6" LCD monitors commonly used with Raspberry Pi devices.
If a monitor is specified as VGA, will the P3 SVGA option drive it OK?
The user manual seems to imply that it will, with the various display
resolutions, but I'd like to be sure before I order either one.

2. The user manual says I can switch the SVGA output on and off. If the
SVGA is on, is the P3's internal display turned off, or is there a way I
can turn it off?

Thanks for any info.

--
73, Mike N4CF
Louisa County, VA USA
Elecraft K3s/100
Carolina Windom up 45'
http://n4cf.mdodd.com
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Alan Bloom]

On 04/22/2016 12:08 PM, Mike Dodd wrote:

> 1. I found some 6" LCD monitors commonly used with Raspberry Pi devices.
> If a monitor is specified as VGA, will the P3 SVGA option drive it OK?
> The user manual seems to imply that it will, with the various display
> resolutions, but I'd like to be sure before I order either one.

It should work as long as it has one of the P3/SVGA's supported screen
resolutions:

- 1024 x 768
- 1280 x 1024
- 1440 x 900
- 1920 x 1080

> 2. The user manual says I can switch the SVGA output on and off. If the
> SVGA is on, is the P3's internal display turned off, or is there a way I
> can turn it off?

You can turn the display brightness to zero with the "LCD Brt" menu item.

Alan N1AL

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]