Re: [KX3] PX3 Questions

[wayne burdick]

Dimensions identical to KX3 case except 2" (5 cm) narrower. Fits in your pocket, should the need arise. Includes KX3-style fold-up tilt feet.

Wayne

----
http://www.elecraft.com

> On Apr 4, 2014, at 4:52 PM, Edouard Lafargue <[hidden email]> wrote:
>
> Speaking about the case: will it be the same depth as the kx3 or slimmer? As slim as possible would make sense to fit it into a travel case...
>
> Ed W6ELA
>
>> On Apr 4, 2014 5:33 PM, "Phil Wheeler" <[hidden email]> wrote:
>>  
>> Case: Good point. I have several kit I build that look ugly because I did the case poorly.
>>
>> Phil W7OX
>>
>>> On 4/4/14, 4:13 PM, Edouard Lafargue wrote:
>>>  
>>>
>>> Nice one! Not easy to get that low power and very wide bw on a homebrew project! And I'm not speaking about the casing which IA often a nightmare on homebrew...
>>>
>>> Ed W6ELA
>>>
>>>> On Apr 4, 2014 4:27 PM, "Wayne Burdick" <[hidden email]> wrote:
>>>>  
>>>> "Michael A. Waldron" wrote:
>>>>
>>>> > So, having had time to digest the datasheet, I have a few questions and I'm sure I'm not alone.
>>>> >
>>>> > Resolution of screen? 200khz is great, but if I can only see 200px it's somewhat less fantastic.
>>>>
>>>> 480 x 272. It's the same LCD we use on the P3.
>>>>
>>>> > Power Source?
>>>>
>>>> 8-15 VDC. Current drain typically 140 mA at 13.8 V. Possible internal battery pack -- plenty of room, though we may or may not offer one.
>>>>
>>>> > I'm sure you guys have worked this out, but I noted no mention of compatibility with the KXPA100?
>>>>
>>>> 100%.
>>>>
>>>> > You guys didn't happen to include a decent speaker in there did you? :)
>>>>
>>>> Only if a PCB vibrates.
>>>>
>>>> > Looking forward to playing with it!
>>>>
>>>> If you want to know what it does beforehand, take at look at the P3 manual. Functional overlap will be better than 90%.
>>>>
>>>> Note: The PX3 requires baseband I/Q signals (available at the KX3's RX I/Q jack); it can't be used with the K3's 8.2-MHz I.F. output.
>>>>
>>>> 73,
>>>> Wayne
>>>> N6KR
>>
>
> __._,_.___
> Reply via web post Reply to sender Reply to group Start a New Topic Messages in this topic (7)
> VISIT YOUR GROUP New Members 27 New Photos 20
> • Privacy • Unsubscribe • Terms of Use
> .
>  
> __,_._,___

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[KD6QZX]

Wayne,  Scott from SideKX here...Can I get an empty case of a PX3 so I can develope my ends and a cover for it, so I can be ready for the rush when they start shipping? 

please call me 714 904 1097 and we can discuss this.  THANKS  Scott AK6Q

 

From: wayne burdick [via Elecraft] <[hidden email]>
To: KD6QZX <[hidden email]>
Sent: Friday, April 4, 2014 5:07 PM
Subject: Re: [KX3] PX3 Questions

Dimensions identical to KX3 case except 2" (5 cm) narrower. Fits in your pocket, should the need arise. Includes KX3-style fold-up tilt feet.

Wayne

----
http://www.elecraft.com/

> On Apr 4, 2014, at 4:52 PM, Edouard Lafargue <[hidden email]> wrote:
>
> Speaking about the case: will it be the same depth as the kx3 or slimmer? As slim as possible would make sense to fit it into a travel case...
>
> Ed W6ELA
>
>> On Apr 4, 2014 5:33 PM, "Phil Wheeler" <[hidden email]> wrote:
>>  
>> Case: Good point. I have several kit I build that look ugly because I did the case poorly.
>>
>> Phil W7OX
>>
>>> On 4/4/14, 4:13 PM, Edouard Lafargue wrote:
>>>  
>>>
>>> Nice one! Not easy to get that low power and very wide bw on a homebrew project! And I'm not speaking about the casing which IA often a nightmare on homebrew...
>>>
>>> Ed W6ELA
>>>
>>>> On Apr 4, 2014 4:27 PM, "Wayne Burdick" <[hidden email]> wrote:
>>>>  
>>>> "Michael A. Waldron" wrote:
>>>>
>>>> > So, having had time to digest the datasheet, I have a few questions and I'm sure I'm not alone.
>>>> >
>>>> > Resolution of screen? 200khz is great, but if I can only see 200px it's somewhat less fantastic.
>>>>
>>>> 480 x 272. It's the same LCD we use on the P3.
>>>>
>>>> > Power Source?
>>>>
>>>> 8-15 VDC. Current drain typically 140 mA at 13.8 V. Possible internal battery pack -- plenty of room, though we may or may not offer one.
>>>>
>>>> > I'm sure you guys have worked this out, but I noted no mention of compatibility with the KXPA100?
>>>>
>>>> 100%.
>>>>
>>>> > You guys didn't happen to include a decent speaker in there did you? :)
>>>>
>>>> Only if a PCB vibrates.
>>>>
>>>> > Looking forward to playing with it!
>>>>
>>>> If you want to know what it does beforehand, take at look at the P3 manual. Functional overlap will be better than 90%.
>>>>
>>>> Note: The PX3 requires baseband I/Q signals (available at the KX3's RX I/Q jack); it can't be used with the K3's 8.2-MHz I.F. output.
>>>>
>>>> 73,
>>>> Wayne
>>>> N6KR
>>
>
> __._,_.___
> Reply via web post Reply to sender Reply to group Start a New Topic Messages in this topic (7)
> VISIT YOUR GROUP New Members 27 New Photos 20
> • Privacy • Unsubscribe • Terms of Use
> .
>  
> __,_._,___

______________________________________________________________

Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net/
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

If you reply to this email, your message will be added to the discussion below:

http://elecraft.365791.n2.nabble.com/Re-KX3-PX3-Questions-tp7586587.html

To unsubscribe from Elecraft, click here.
NAML