Re: Shipping Status

[M0XDF]

Well, I had half expected it and was hoping it wouldn't be late (as I'm sure
lots were) and I agree with the others, do it right.

I had hoped I'd have it at the beginning of Aug, not so I could assemble it
- too much going on in Aug for that. But so I could read the manual during
my 2 week vacation at the end of Aug.
Is there any chance of an early release of the manual in electronic form?

--
If all our misfortunes were laid in one common heap whence everyone must
take an equal portion, most people would be contented to take their own and
depart.
-Socrates (469?-399 B.C.)


_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[AC7AC]

CONTENTS DELETED

The author has deleted this message.

[Simon (HB9DRV)]

Maybe when final orders are confirmed by sales we can say that we do NOT
want the manuals, I would rather download the latest from the web rather
than have half a rain forest shipped to Switzerland.

Simon Brown, HB9DRV

----- Original Message -----
From: "Ron D'Eau Claire" <[hidden email]>

The problem is that the documentation, including the Owner's Manual and the
kit Assembly Manual, will be finished *after* the last changes to the K3 are
made and tested!

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Julian, G4ILO]

On 7/24/07, Simon Brown (HB9DRV) <[hidden email]> wrote:
> Maybe when final orders are confirmed by sales we can say that we do NOT
> want the manuals, I would rather download the latest from the web rather
> than have half a rain forest shipped to Switzerland.

I hope that a printed copy will be included with the kit. [Rest of
original reply deleted due to rejection by stupid qth.net spam
filters]
--
Julian, G4ILO K2 s/n: 392  K3 s/n: ???
G4ILO's Shack: www.g4ilo.com
Ham-Directory: www.ham-directory.com
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Dick Dickinson]

Does someone have a cut and paste copy of the K3 mic pinout that they can
post?


Regards,
Dick - KA5KKT/4

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Don Wilhelm-3]

Dick,

It is the same as the 'Elecraft' mic pinout shown in the KSB2 manual.
You can download it from the Elecraft website if you don't have a copy.

The bias resistor can be switched in or out via menu selections.

IIRC, the front and back panel jacks can be independent (one with bias
set on, one without).

73,
Don W3FPR

Edward Dickinson III wrote:
> Does someone have a cut and paste copy of the K3 mic pinout that they can
> post?
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Ed Muns, W0YK]

Note that the rear panel microphone connector is a 3.5mm mono phone jack
whereas the front panel connector is the standard 8-pin microphone jack.
Only one connector can be enabled at a time and bias can be selected, or
not, to that active connector.  Any microphone plugged into the unselected
jack is invisible to the radio.

73,
Ed - W0YK

> -----Original Message-----
> From: [hidden email]
> [mailto:[hidden email]] On Behalf Of Don Wilhelm
> Sent: Tuesday, 24 July, 2007 08:42
> To: Edward Dickinson III
> Cc: 'elecraft'
> Subject: Re: [Elecraft] K3 Mic Pinout
>
> Dick,
>
> It is the same as the 'Elecraft' mic pinout shown in the KSB2 manual.
> You can download it from the Elecraft website if you don't
> have a copy.
>
> The bias resistor can be switched in or out via menu selections.
>
> IIRC, the front and back panel jacks can be independent (one
> with bias set on, one without).
>
> 73,
> Don W3FPR
>
> Edward Dickinson III wrote:
> > Does someone have a cut and paste copy of the K3 mic pinout
> that they
> > can post?
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
>  http://mailman.qth.net/mailman/listinfo/elecraft   
>
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Tom Hammond-2]

Dick - KA5KKT/4 wrote:

>Does someone have a cut and paste copy of the K3 mic pinout that they can
>post?

K3 Mic plug wiring:

1 Mic Audio (with bias)
2 /PTT
3 DN (ignored for now)
4 UP (ignored for now)
5 FUNC (ignored for now)
6 BIAS
7 GND
8 GND

73,

Tom Hammond   N0SS

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[AJSOENKE]

Likewise, it would be nice to have the manual online as soon as it is  
complete. Add the time it takes to produce printed copies and ship to far off  
destinations, I'd at least like a chance to have a look while waiting.
Not to mention there's no need to hold up hardware deliveries while the  
books printed.
 
Al WA6VNN



************************************** Get a sneak peek of the all-new AOL at
http://discover.aol.com/memed/aolcom30tour
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com