Slight problem with adjusting power output

[Gary McKelvie]

Hi to the List,

OK here goes when I use the power dial to adjust the Power out on the
K2 I get on the LCD the keyer speed being adjusted.
This also happens when I use the keyer dial.

I've checked that every thing worked fine and dandy up to the stage 2
alignment (40m receive).
I 'm not sure where I've mucked it up as I can't see any
shorts,components not soldered or components in the wrong place on
any of the boards.

At present I'm stuck on the 40m transmitter alignment so haven't set
up the other bands for receive or transmit yet.
Any ideas/suggestions what to check greatly appreciated. :)

73 Gary

Gary McKelvie
G7USC
Web : www.garym.org.uk
Mobile : [phone]
MSN Messenger : [hidden email]
So Long and Thanks for all the Fish

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Gary McKelvie]

Hi Tom,

Thanks it was D5 that was incorrectly orientated.
I did also touch the soldering iron to U3 at the same time but
definitely it was D5 the wrong way round.
Much appreciated.

73 de Gary G7USC

At 18:04 20/05/2007, you wrote:
>Hi Gary!
>On the Front Panel Board check the following:
>Orientation og D4 and D5.
>Also check for a short between pin 6 and 7 on U3.
>My bet is a short on pin 6 and 7 on U3
>
>Let me know what u find Gary.
>
>73 de Tom LA1PHA

Gary McKelvie
G7USC
Web : www.garym.org.uk
Mobile : [phone]
MSN Messenger : [hidden email]
So Long and Thanks for all the Fish

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Tom Arntzen-2]

Glad to hear Gary!
Good luck with the rest!

Tom

----- Original Message -----
From: "Gary McKelvie" <[hidden email]>
To: "Tom Arntzen" <[hidden email]>
Cc: "Elecraft Support List" <[hidden email]>
Sent: Sunday, May 20, 2007 8:01 PM
Subject: Re: [Elecraft] Slight problem with adjusting power output

> Hi Tom,
>
> Thanks it was D5 that was incorrectly orientated.
> I did also touch the soldering iron to U3 at the same time but definitely
> it was D5 the wrong way round.
> Much appreciated.
>
> 73 de Gary G7USC
>
> At 18:04 20/05/2007, you wrote:
>>Hi Gary!
>>On the Front Panel Board check the following:
>>Orientation og D4 and D5.
>>Also check for a short between pin 6 and 7 on U3.
>>My bet is a short on pin 6 and 7 on U3
>>
>>Let me know what u find Gary.
>>
>>73 de Tom LA1PHA
>
> Gary McKelvie
> G7USC
> Web : www.garym.org.uk
> Mobile : [phone]
> MSN Messenger : [hidden email]
> So Long and Thanks for all the Fish
>
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition. Version: 7.5.467 / Virus Database:
> 269.7.6/813 - Release Date: 20.05.2007 07:54
>
>

--
Jeg bruker gratisversjonen av SPAMfighter for privatbrukere.
 Den har fjernet 80 søppelpostmeldinger til nå.
Betalende brukere har ikke denne meldingen i e-postene sine.
Få tak i SPAMfighter gratis her: http://www.spamfighter.com/lno


_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com