Z6, grounded can?

[dave.wilburn]

I'm installing T6 (yes there is a god, this is the last of the toroids
for a little bit) and noticed a hole next to Z6.  I did not see anything
in the text, but the holes on either side of the can are in the ground
plane so I was not sure.
--

David Wilburn
[hidden email]

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Don Wilhelm-3]

Dave,

Congratulations on your progress.

Don't worry about the empty holes - all holes are not filled, many are via
holes to get a signal (or ground) from the top of the board to the bottom.
If you need to check anything else of that nature, look at the parts
placement diagram near the end of the manual, you will find it quite
helpful.  It does not show the holes, just the component placements.

73,
Don W3FPR

> -----Original Message-----
>
> I'm installing T6 (yes there is a god, this is the last of the toroids
> for a little bit) and noticed a hole next to Z6.  I did not see anything
> in the text, but the holes on either side of the can are in the ground
> plane so I was not sure.
> --
>
> David Wilburn
> [hidden email]

>
--
No virus found in this outgoing message.
Checked by AVG Free Edition.
Version: 7.5.441 / Virus Database: 268.18.1/690 - Release Date: 2/16/2007
2:25 PM

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[dave.wilburn]

FB, it was just that we had grounded all the other cans, so I wasn't
sure.  Thanks.

David Wilburn
[hidden email]



Don Wilhelm wrote:

> Dave,
>
> Congratulations on your progress.
>
> Don't worry about the empty holes - all holes are not filled, many are via
> holes to get a signal (or ground) from the top of the board to the bottom.
> If you need to check anything else of that nature, look at the parts
> placement diagram near the end of the manual, you will find it quite
> helpful.  It does not show the holes, just the component placements.
>
> 73,
> Don W3FPR
>
>> -----Original Message-----
>>
>> I'm installing T6 (yes there is a god, this is the last of the toroids
>> for a little bit) and noticed a hole next to Z6.  I did not see anything
>> in the text, but the holes on either side of the can are in the ground
>> plane so I was not sure.
>> --
>>
>> David Wilburn
>> [hidden email]
>
> --
> No virus found in this outgoing message.
> Checked by AVG Free Edition.
> Version: 7.5.441 / Virus Database: 268.18.1/690 - Release Date: 2/16/2007
> 2:25 PM
>
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com