Elecraft

alignement KPA100

Classic

List

Threaded

4 messages Options

Christophe aufacf

alignement KPA100

hello to all ,

I am subscribed to the elecraft list, I receive the list well but I am
unable to send messages

would it be possible for you to see what's going on?

thank you in advance I would like to continue my K2 after 3 years of
stopping

as i need to ask questions thanks again

--
73 , F8ACF56
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

Don Wilhelm

Re: alignement KPA100

Your post made it to the reflector OK.
You must use plain text, HTML will be rejected.
Direct email to [hidden email].

What is your problem with the K2 and KPA100? The instructions for
alignment of the KPA100 are in the manual.

73,
Don W3FPR

On 4/5/2020 3:12 PM, Christophe aufacf wrote:

> hello to all ,
>
> I am subscribed to the elecraft list, I receive the list well but I am
> unable to send messages
>
> would it be possible for you to see what's going on?
>
> thank you in advance I would like to continue my K2 after 3 years of
> stopping
>
> as i need to ask questions thanks again
>
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

Christophe aufacf

Re: alignement KPA100

hello Don, hello everyone,

I would like to be sure about 2 measurements on page 44 for my KPA100
Q9 tab: tad; is this the radiator? infinite measure
for the central pin of J2, I also find: infinite

the question is are the measurements good?

the whole thing being to have a good base

thank you Don and all of you for your help

# K2 7369 + KPA100 in progress

Le dim. 5 avr. 2020 à 22:09, Don Wilhelm <[hidden email]> a écrit :

>
> Your post made it to the reflector OK.
> You must use plain text, HTML will be rejected.
> Direct email to [hidden email].
>
> What is your problem with the K2 and KPA100? The instructions for
> alignment of the KPA100 are in the manual.
>
> 73,
> Don W3FPR
>
> On 4/5/2020 3:12 PM, Christophe aufacf wrote:
> > hello to all ,
> >
> > I am subscribed to the elecraft list, I receive the list well but I am
> > unable to send messages
> >
> > would it be possible for you to see what's going on?
> >
> > thank you in advance I would like to continue my K2 after 3 years of
> > stopping
> >
> > as i need to ask questions thanks again
> >
> >

--
73 , F8ACF56
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

Dave Van Wallaghen-2

Re: alignement KPA100

F8ACF56,

Q9 provides the KEY OUT signal to key an external amplifier (or other
circuit) when the KPA100 PTT is actuated. Normally, this signal (tab or
drain of Q9) will measure open or infinite. It will then measure close
to 0 ohms when the KPA100 is keyed (PTT actuated).

Measuring infinite at J2 is also fine. I know the instructions say >10K
for both measurements, but infinite is fine (and > 10K).

73,
Dave W8FGU

------ Original Message ------
From: "Christophe aufacf" <[hidden email]>
To: [hidden email]
Cc: [hidden email]
Sent: 4/6/2020 5:17:29 AM
Subject: Re: [Elecraft] alignement KPA100

>hello Don, hello everyone,
>
>I would like to be sure about 2 measurements on page 44 for my KPA100
>Q9 tab: tad; is this the radiator? infinite measure
>for the central pin of J2, I also find: infinite
>
>the question is are the measurements good?
>
>the whole thing being to have a good base
>
>thank you Don and all of you for your help
>
># K2 7369 + KPA100 in progress
>
>
>Le dim. 5 avr. 2020 à 22:09, Don Wilhelm <[hidden email]> a écrit :
>>
>> Your post made it to the reflector OK.
>> You must use plain text, HTML will be rejected.
>> Direct email to [hidden email].
>>
>> What is your problem with the K2 and KPA100? The instructions for
>> alignment of the KPA100 are in the manual.
>>
>> 73,
>> Don W3FPR
>>
>> On 4/5/2020 3:12 PM, Christophe aufacf wrote:
>> > hello to all ,
>> >
>> > I am subscribed to the elecraft list, I receive the list well but I am
>> > unable to send messages
>> >
>> > would it be possible for you to see what's going on?
>> >
>> > thank you in advance I would like to continue my K2 after 3 years of
>> > stopping
>> >
>> > as i need to ask questions thanks again
>> >
>> >
>
>
>
>--
>73 , F8ACF56
>______________________________________________________________
>Elecraft mailing list
>Home: http://mailman.qth.net/mailman/listinfo/elecraft
>Help: http://mailman.qth.net/mmfaq.htm
>Post: mailto:[hidden email]
>
>This list hosted by: http://www.qsl.net
>Please help support this email list: http://www.qsl.net/donate.html
>Message delivered to [hidden email]