Hello all,
I just started the inventory of parts for my kat2 and all is going well until I got to the "102" caps. For the life of me I cannot determine the two smaller ones! I have lined them up with a ruler on a marble top table and looked at them from all angles. All 26 appear to be the same size. Any suggestions? Secondly, thetwo trimmer potentiometers are listed at 100k but 150k was shipped. A problem? 73 all Dan Daniel Grizzard Extra Class af4lb ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
A suggestion from QST I have used with success is to photograph the
parts with a digital camera on it's highest resolution setting and enlarge them on the computer. Just be sure not to get too close or your lens may not be able to focus. If you have a macro setting, that can help too. Don't worry about being a foot or two away: modern cameras can make the tiniest part large. 73, Byron N6NUL On Sunday, January 2, 2011, Dan Grizzard <[hidden email]> wrote: > Hello all, > > I just started the inventory of parts for my kat2 and all is going well until I got to the "102" caps. For the life of me I cannot determine the two smaller ones! > I have lined them up with a ruler on a marble top table and looked at them from all angles. All 26 appear to be the same size. Any suggestions? -- - Northern California Contest Club - CU in the 2011 Cal QSO Party 1-2 Oct 2011 - www.cqp.org ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
In reply to this post by Dan Grizzard
Dan,
The trimmer pots are OK, use the 150k value. The capacitors are a different matter, there are two that must fit between the processor socket and the header to the L/C board. The .001 uF capacitors seem to have become "fatter" over the years due to manufacturing changes. Check to see if you have 2 extra .001 uF capacitors somewhere in the kit. As I recall, there were 2 disc ceramics in the last KAT2 kit I built (but then I may have pulled them out of my parts drawer, my memory can be "fuzzy". There was a period of time when the errata sheet was included, but the parts ECO had not yet been updated. So if you purchased the kit a few months ago and are just now getting around to building it, you may indeed have those capacitors missing - if so, contact [hidden email]. Explain carefully so that you receive the thin capacitors There is no part number given in the errata sheet, but I know PN E530072 will work just fine even if you have to form the leads for the wider spacing. 73, Don W3FPR On 1/2/2011 11:58 AM, Dan Grizzard wrote: > Hello all, > > I just started the inventory of parts for my kat2 and all is going well until I got to the "102" caps. For the life of me I cannot determine the two smaller ones! > I have lined them up with a ruler on a marble top table and looked at them from all angles. All 26 appear to be the same size. Any suggestions? > > Secondly, thetwo trimmer potentiometers are listed at 100k but 150k was shipped. A problem? > 73 all > Dan > > Daniel Grizzard > Extra Class > af4lb > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
Free forum by Nabble | Edit this page |