modification K2 use for KPA100

[Christophe aufacf]

Good afternoon all

for the modifications of the K2 to put a KPA100

must be done before putting the KPA100 so measurement and adjustments

or can this be done once KP100 is set and installed?

could give me the page in the manual of K2 or aligns 12 / 10M ?

thank you in advance, I'm happy to get back on my K2 after more than 3
years off, so I have to get back in the bath

# K2 7369 + KPA100 in progress


--
73 , F8ACF56
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Don Wilhelm]

Christophe,

Since your K2 is SN 7369, it does not need any modifications or
alignment to add the KPA100 - that 10/12m VFO/ALC Mod kit is only for
older K2s, those component changes are already present in your K2.

You will have to add the headers on the RF Board if they are not already
present.  The KPA100 manual will tell you when to install them.

73,
Don W3FPR

On 4/6/2020 4:03 PM, Christophe aufacf wrote:

> Good afternoon all
>
> for the modifications of the K2 to put a KPA100
>
> must be done before putting the KPA100 so measurement and adjustments
>
> or can this be done once KP100 is set and installed?
>
> could give me the page in the manual of K2 or aligns 12 / 10M ?
>
> thank you in advance, I'm happy to get back on my K2 after more than 3
> years off, so I have to get back in the bath
>
> # K2 7369 + KPA100 in progress
>
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Christophe aufacf]

hello don  and All ,

Thank you for the info

I'm going back to my K2

73 , F8ACF

#K2 7369 + KP100 in progress

Le lun. 6 avr. 2020 à 23:33, Don Wilhelm <[hidden email]> a écrit :

>
> Christophe,
>
> Since your K2 is SN 7369, it does not need any modifications or
> alignment to add the KPA100 - that 10/12m VFO/ALC Mod kit is only for
> older K2s, those component changes are already present in your K2.
>
> You will have to add the headers on the RF Board if they are not already
> present.  The KPA100 manual will tell you when to install them.
>
> 73,
> Don W3FPR
>
> On 4/6/2020 4:03 PM, Christophe aufacf wrote:
> > Good afternoon all
> >
> > for the modifications of the K2 to put a KPA100
> >
> > must be done before putting the KPA100 so measurement and adjustments
> >
> > or can this be done once KP100 is set and installed?
> >
> > could give me the page in the manual of K2 or aligns 12 / 10M ?
> >
> > thank you in advance, I'm happy to get back on my K2 after more than 3
> > years off, so I have to get back in the bath
> >
> > # K2 7369 + KPA100 in progress
> >
> >

--
73 , F8ACF56
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]