Posted by
Darwin, Keith on
Dec 07, 2005; 9:34pm
URL: http://elecraft.85.s1.nabble.com/Clever-antenna-tuning-ideas-wanted-tp384403p384409.html
My antenna is similar. 28.5' tall, ground mounted over twelve 28' long
radials. Fed with 30 feet of RG-213. With a tuner the system works
well enough on 40, 30, 20, 15. 80 Meters is the pits. Dummy Load City!
I'm considering putting a remote ATU at the base of the antenna.
Basically, eliminating the 30 feet of coax feed line and all the high
VSWR losses it entails.
I picked 28 feet for the vertical to make it a reasonable impedance on
each of my bands of interest (as well as to increase wind
survivability).
Another thought I've had is to put a Hustler 80 M resonator on top of it
to raise the feed point impedance on 80. For now, I'll have to stick
with 40 meters.
- Keith KD1E -
-----Original Message-----
From:
[hidden email]
[mailto:
[hidden email]] On Behalf Of Vic K2VCO
Sent: Wednesday, December 07, 2005 4:20 PM
To: Elecraft Reflector
Subject: [Elecraft] Clever antenna tuning ideas wanted
OK, here is what I want to do:
I have a 33' (10m) vertical with the base about 10' (3.3m) above ground.
It has four 8' (2.4m) radials which are connected to the feedpoint
through a coil which resonates the system on 7 MHz. It works as well or
better than any vertical that I've used on 40m -- low SWR and good
results. It's fed through a relatively short (20', 6m) length of
RG-213.
I would like to use it on 80m and 30m as well. My first try was to
simply use the KAT100 to tune it. It tunes fine on both bands (1:1 at
the rig), but results are fair-to-poor on 30 and poor-to-worthless on
80.
On 30m, the coax losses are reasonable (the SWR on the coax is about 8
to 1, but it's very short). I suspect the problem is that the radial
ground system is very poor on this band (on the other hand, the long
vertical radiator should provide a slight amount of gain). So I may try
paralleling a set of radials tuned for 30m. They will also be short,
but resonated with a coil or stub. Does this sound like a good
analysis/solution?
On 80m, it's more complicated. The ground system is terrible, the
radiation resistance of the vertical very low, and the SWR and losses on
the coax very high. No wonder it's a dummy load! I guess the way to
deal with it is to add more tuned radials in parallel and a switchable
base network, but I would like to avoid any more control wires that have
to go through my lightning suppression panel (I can't pass DC through
the coax, either). Does anyone have any suggestions?
--
73,
Vic, K2VCO
Fresno CA
http://www.qsl.net/k2vco_______________________________________________
Elecraft mailing list
Post to:
[hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help:
http://mailman.qth.net/subscribers.htmElecraft web page:
http://www.elecraft.com_______________________________________________
Elecraft mailing list
Post to:
[hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help:
http://mailman.qth.net/subscribers.htmElecraft web page:
http://www.elecraft.com