RE: Somewhat high transmit current K2

Posted by Don Wilhelm-3 on Dec 08, 2005; 3:13am
URL: http://elecraft.85.s1.nabble.com/Somewhat-high-transmit-current-K2-tp384417p384418.html

If you have checked the low pass filter area carefully, then the next place
to check is T4 - you should have 2 loops (green) on one side and 3 loops
(white) on the other.  Make certain that the links are correct - they are
not full turns but go through only one side of the binocular core.

T3 is the next thing after T4 - be certain it is well soldered and the
bi-filar turns are laying next to each other.

Then check T1 and T2 - these are not usually suspect in lower than normal
gain situations, but make certain the turns are correct.

If all else fails, you may want to try replacing Q5 to see if the
replacement has higher gain than the one you have installed.

Your real problem seems to be lower than normal gain from the input to Q5 to
the output - low gain makes the driver and finals work harder to produce the
requested output and thus draw more than the usual amount of current.

Lastly, your 2.8 Amps is only about 10% higher than the norm, so if you
can't find anything that is an easy fix, you may just want to accept it as
is.

73,
Don W3FPR

> -----Original Message-----
> From: [hidden email]
> [mailto:[hidden email]]On Behalf Of Lambs, Dick & Judy
> Sent: Wednesday, December 07, 2005 8:04 PM
> To: Elecraft - Maling List Elecraft - Mailing List
> Subject: [Elecraft] Somewhat high transmit current K2
>
>
> I'd appreciate suggestions for finding the cause of somewhat elevated
> transmit current on my K2 (serial 02165).
>
> On 7.1 MHz, with all options removed, at full output (about 15 W to a
> 50 Ohm perfect dummy load) the K2 displays 2.8 A.   Other bands are
> similar.
>
> This is with actual 13.8 V from the supply.  An independent ammeter
> in the supply line agrees closely.  The supply voltage drops to 13.5
> on transmit as measured at the K2 connector.  The internal K2 display
> shows 13.4 V and 0.22 A on receive, with voltage dropping to 12.7 on
> transmit.
>
> I’ve checked toroid values (color and turns count through hole) and
> all other components in the bandpass, lowpass, pre-driver, and driver
> circuits.
>
> I’ve listed below signal tracing Vrms values below for the
> transmitter stages at 5 W output.  Compared to the values in the
> signal tracing section of my manual, the Xmit mixer and buffer
> outputs are low, but output from the bandpass filter is OK. The pre-
> driver output is low.  The signal voltage on the driver input is very
> low.  However, the driver output is OK.
>
> The DC voltages on the pre-driver, driver, and PA amp transistors
> agree roughly with the manual values.
>
> I don’t know where to go next.  Any ideas?
>
>     *******************************
>
> Signal tracing values Vrms (expected/actual)
>
> Xmit Mixer Output:  .0016/.008
> Buffer Output:  .200/.065
> Band-pass Filter Output:  .030/.025
> T-R Switch #1 Output:  .029/.023
> Pre-Driver Otuput:  .120/.061
> Driver Input:  .026/.006
> Driver Output:  1.8/1.8
> PA Input:  .38/.41
> RF Detector Input:  2.0/2.0
>
>    **********************************
>
> Thanks
> Dick, K0KK
>
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
>  http://mailman.qth.net/mailman/listinfo/elecraft
>
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.1.371 / Virus Database: 267.13.12/193 - Release Date: 12/6/2005
>
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com