Posted by
Clay Autery-2 on
Jun 08, 2018; 2:01pm
URL: http://elecraft.85.s1.nabble.com/Default-K3-transmit-delay-may-be-too-short-for-slow-QRO-amplifiers-tp7641779p7641793.html
Mmmmm.... even without a firmware change, my TX DLY already has the
range from "NOR 8ms" to "020" (8-20 ms). Granted, that 20ms MAY be
somewhat shorter than 20ms, as described by Wayne regarding the 8ms
"NOR" setting.
I suspect that they will now push this up in the queue of things to mod
in the next firmware release.
Strange (to me) that so many find foot switch use in CW such a
non-starter. Since I uses one exclusively in SSB, I guess it is only
natural for me to use one in CW...
73,
______________________
Clay Autery, KY5G
(318) 518-1389
On 08-Jun-18 05:22, Igor Sokolov wrote:
> Wayne it is a pity that TX delay setting affects CW timing. Changing
> TX delay from default even one or two steps makes CW much worth. Can
> you figure out a way to make CW timing independent from TX delay? With
> 5 ms TX delay working in many contests I already had to change a pair
> of relays in the amplifier. 10-12 ms would be fine for me. 20 ms will
> probably suit the majority of users. But 5 ms is way too fast and
> unfortunately cannot be altered without spoiling CW sending. I know
> that I could build external sequencer but this does not look neat
> enough especially for portable field operation. Every other radio I
> had allowed TX delay adjustment to at least 20 ms.
>
> 73, Igor UA9CDC
>
> 08.06.2018 4:43, Wayne Burdick пишет:
>> It has come to our attention (thanks to N7YK and N6TV) that the
>> default value of CONFIG:TX DLY, 8 ms, may actually be closer to 5 ms.
>>
>> The associated T/R control firmware hasn’t changed in a long time, so
>> hopefully there aren’t many users affected (or we would have heard
>> about it). The shorter delay may be related to the improved KSYN3A
>> synth, which switches faster than the original. We’re looking into
>> this, and will update the displayed value to reflect the actual value.
>>
>> Details:
>>
>> When using a QRO amp with the K3, the KEY OUT line from the radio is
>> used to key the amplifier, setting it up to receive RF. Since the K3
>> has very fast QSK, the amp’s T/R control circuitry has to be
>> similarly fast.
>>
>> Those of you who are using KPA500s and KPA1500s need not be concerned
>> about the K3’s fast QSK speed, since our amps use PIN diode T/R
>> switching. They can easily keep up with the K3 at any code speed and
>> with the default setting of the CONFIG:TX DLY menu entry.
>>
>> However, some other amps, especially older ones, use slow T/R relays.
>> If the transceiver generates RF before the amp is ready, this might
>> result in key clicks.
>>
>> (In practice there’s a bit of a grace period because the RF keying
>> envelope rises very slowly. It’s a "raised-cosine sigmoid," resulting
>> in the transceiver itself having incredibly clean keying sidebands.
>> See K9YC white paper on this topic.)
>>
>> If you suspect your amp has a slow T/R relay, you should do a
>> listening test, or better yet have someone else listen from a good
>> distance. If you (or they) hear any evidence of clicks, increase the
>> value of CONFIG:TX DLY.
>>
>> Use the lowest setting that eliminates the clicks. CW keying at
>> higher code speeds may be affected if the value is too high. Other
>> modes not using fast QSK will generally be unaffected (voice and data).
>>
>> An alternative to increasing TX DLY is to use a foot switch, as do
>> many users of old amps regardless of transceiver type.
>>
>> 73,
>> Wayne
>> N6KR
______________________________________________________________
Elecraft mailing list
Home:
http://mailman.qth.net/mailman/listinfo/elecraftHelp:
http://mailman.qth.net/mmfaq.htmPost: mailto:
[hidden email]
This list hosted by:
http://www.qsl.netPlease help support this email list:
http://www.qsl.net/donate.htmlMessage delivered to
[hidden email]