Archives and 160 no TX

[Rich McCabe]

Didn't there used to be archives of this mail list somewhere that someone
indexed?

I just installed my 160 board and have no TX. I was getting sleepy when I
finished it so might have been "dumb" :)

I seemed to remember something from the last K2 I built but cant remember.
Can someone direct me to where that is located if its still around?

Thanks,

Rich


_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft   
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Rich McCabe]

Well found the archives so nevermind on that. I was being sleepy last not
and forgot to do the CAL PLL. But now when I try it at 1800.10 I get an Info
232 error.

Any ideas?


----- Original Message -----
From: "Rich McCabe" <[hidden email]>
To: "Elecraft Reflector" <[hidden email]>
Sent: Wednesday, August 25, 2004 5:24 PM
Subject: Archives and 160 no TX

> Didn't there used to be archives of this mail list somewhere that someone
> indexed?
>
> I just installed my 160 board and have no TX. I was getting sleepy when I
> finished it so might have been "dumb" :)
>
> I seemed to remember something from the last K2 I built but cant remember.
> Can someone direct me to where that is located if its still around?
>
> Thanks,
>
> Rich
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft   
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Rich McCabe]

Nevermind
:0
----- Original Message -----
From: "Rich McCabe" <[hidden email]>
To: "Elecraft Reflector" <[hidden email]>
Sent: Wednesday, August 25, 2004 5:39 PM
Subject: Re: Archives and 160 no TX


> Well found the archives so nevermind on that. I was being sleepy last not
> and forgot to do the CAL PLL. But now when I try it at 1800.10 I get an
Info

> 232 error.
>
> Any ideas?
>
>
> ----- Original Message -----
> From: "Rich McCabe" <[hidden email]>
> To: "Elecraft Reflector" <[hidden email]>
> Sent: Wednesday, August 25, 2004 5:24 PM
> Subject: Archives and 160 no TX
>
>
> > Didn't there used to be archives of this mail list somewhere that

someone
> > indexed?
> >
> > I just installed my 160 board and have no TX. I was getting sleepy when
I
> > finished it so might have been "dumb" :)
> >
> > I seemed to remember something from the last K2 I built but cant
remember.
> > Can someone direct me to where that is located if its still around?
> >
> > Thanks,
> >
> > Rich
> >
>


_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft   
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Rich McCabe]

Thanks guys. She is working now, just dont have squat for drive on SSB. When
I "tune" she looks good but the MD2 will barely get a couple watts.

Keep tweaking :)

Rich
----- Original Message -----
From: "W9DHI" <[hidden email]>
To: "'Rich McCabe'" <[hidden email]>
Sent: Wednesday, August 25, 2004 6:33 PM
Subject: RE: [Elecraft] Re: Archives and 160 no TX

> You always have to run Cal on 40 meters......that's an errata in the 160
> manual.
>
>
> Gregg R. Lengling, W9DHI, Retired
> Administrator http://www.milwaukeehdtv.org
> K2/100 S#3075 KX1 S# 57
> Member:  ARRL, RSGB, RCA, WERA and ORC
>
>
>
> -----Original Message-----
> From: [hidden email]
> [mailto:[hidden email]] On Behalf Of Rich McCabe
> Sent: Wednesday, August 25, 2004 5:40 PM
> To: Elecraft Reflector
> Subject: [Elecraft] Re: Archives and 160 no TX
>
> Well found the archives so nevermind on that. I was being sleepy last not
> and forgot to do the CAL PLL. But now when I try it at 1800.10 I get an

Info

> 232 error.
>
> Any ideas?
>
>
> ----- Original Message -----
> From: "Rich McCabe" <[hidden email]>
> To: "Elecraft Reflector" <[hidden email]>
> Sent: Wednesday, August 25, 2004 5:24 PM
> Subject: Archives and 160 no TX
>
>
> > Didn't there used to be archives of this mail list somewhere that

someone
> > indexed?
> >
> > I just installed my 160 board and have no TX. I was getting sleepy when
I
> > finished it so might have been "dumb" :)
> >
> > I seemed to remember something from the last K2 I built but cant
remember.

> > Can someone direct me to where that is located if its still around?
> >
> > Thanks,
> >
> > Rich
> >
>
>
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
> http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
>
>
>
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft   
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com