Autoinfo 1

[srife]

    I set Autoinfo to Auto1 and it did not seem to cause the K3 to send
out RS-232 data without being polled. My impression is that this is what
this option was supposed to do. I may be out in left field on this, and
if so someone bring me in out of the rain please. :-)

    I am trying to get the K3 to send data out for the SteppIR antenna
to read without having HRD running. There are times when I would like to
just peruse the bands without wanting the software running, but have the
SteppIR track the frequency. Has anyone done this successfully?

--
Stan
W5EWA
Houston, TX
K2/100 SN 4216
K3/100 SN 0690

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[N2TK]

Hi Stan,
At the moment my desktop PC is off but my SteppIR is tracking my K3. I have
Autoinfo set to "1".
I have a "Y" connector on the RS232 cable going from the K3 to the SteppIR
to the PC. I assume you have the SteppIR in "General" mode. On the SteppIR I
have mode =KENW and Baud=4800.
GL
N2TK, Tony

-----Original Message-----
From: [hidden email]
[mailto:[hidden email]] On Behalf Of Stan Rife
Sent: Sunday, June 15, 2008 7:57 PM
To: Elecraft
Subject: [Elecraft] Autoinfo 1

    I set Autoinfo to Auto1 and it did not seem to cause the K3 to send
out RS-232 data without being polled. My impression is that this is what
this option was supposed to do. I may be out in left field on this, and
if so someone bring me in out of the rain please. :-)

    I am trying to get the K3 to send data out for the SteppIR antenna
to read without having HRD running. There are times when I would like to
just peruse the bands without wanting the software running, but have the
SteppIR track the frequency. Has anyone done this successfully?

--
Stan
W5EWA
Houston, TX
K2/100 SN 4216
K3/100 SN 0690

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Dick Dievendorff]

If you set AI1; and then turn the VFO A knob, hopefully you'll see an IF
packet sent within a second or so of changing the frequency.

The initial implementation in an early firmware version spewed data once a
second whether anything had changed or not.

Now AI1; sends the IF packet only when a frequency setting changes.

See the K3 Programmer's Reference for details.

You can use the K3 Utility's command tester to observe this behavior.

73 de Dick, K6KR




-----Original Message-----
From: [hidden email]
[mailto:[hidden email]] On Behalf Of Stan Rife
Sent: Sunday, June 15, 2008 4:57 PM
To: Elecraft
Subject: [Elecraft] Autoinfo 1

    I set Autoinfo to Auto1 and it did not seem to cause the K3 to send
out RS-232 data without being polled. My impression is that this is what
this option was supposed to do. I may be out in left field on this, and
if so someone bring me in out of the rain please. :-)

    I am trying to get the K3 to send data out for the SteppIR antenna
to read without having HRD running. There are times when I would like to
just peruse the bands without wanting the software running, but have the
SteppIR track the frequency. Has anyone done this successfully?

--
Stan
W5EWA
Houston, TX
K2/100 SN 4216
K3/100 SN 0690

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com