Front Panel Board K2 06014 wheres RP3 10K 8 pin

[glblock]

Ok, confused here.  On page 28 of the Owners Manual it says to check off the
items NOT installed.  If I have the SSB kit, which I do, it says to install them
now.

RP3 has some issues.. it says its a 10k resistor network and is supplied in the
SSB kit.  The board shows it as an 8 pin inline part.  The SSB parts had all the
parts BUT describes RP3 as a 2K 6 pin resistor network AND there is NO 10K
inline pin resistor chip in the SSB bag to put in the front panel board.

What goes in the RP3 slot on the Front panel board.  In the SSB manual it
describes RP3 as a 10K 8 pin but on page 3 RP3 is a 2.0K 6 pin ???

confused..
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Don Wilhelm-3]

There should be two 'RP3's in the KSB2 kit.  One is the RP2 (2.0k 6 pin)
that will be mounted on the KSB2 board - the other should be the 8 pin RP3
(10K) that will mount on the Front Panel board.
Look at the parts list carefully, it indicates first the components that go
onto the KSB2 board and further down it indicates the components that go
onto the Front Panel board.

Inventory your entire KSB2 kit contents before proceeding and if you have
any missing components, send a note to mailto:[hidden email] and the
needed parts should be sent to you promptly.

73,
Don W3FPR

> -----Original Message-----
>
> Ok, confused here.  On page 28 of the Owners Manual it says to
> check off the
> items NOT installed.  If I have the SSB kit, which I do, it says
> to install them
> now.
>
> RP3 has some issues.. it says its a 10k resistor network and is
> supplied in the
> SSB kit.  The board shows it as an 8 pin inline part.  The SSB
> parts had all the
> parts BUT describes RP3 as a 2K 6 pin resistor network AND there is NO 10K
> inline pin resistor chip in the SSB bag to put in the front panel board.
>
> What goes in the RP3 slot on the Front panel board.  In the SSB manual it
> describes RP3 as a 10K 8 pin but on page 3 RP3 is a 2.0K 6 pin ???
>
> confused..
>

--
No virus found in this outgoing message.
Checked by AVG Free Edition.
Version: 7.5.441 / Virus Database: 268.17.37/682 - Release Date: 2/12/2007
1:23 PM

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Brian Broggie-2]

And this will only get more confusing before it gets better.

There are actually two references of RP3 on page 3 of the Parts list.  
The first is line 1, as you have found.  The second one is on line 18
(or line 4 under the heading "Components on Front Panel Board").  There
is where you'll find your 10K, 8 pin resistor pack listed.

Of course, this is all moot if you don't actually have an 8 pin resistor
pack in your kit!  For that you should contact [hidden email] and
ask for part #E510005.

Brian, W6FVI
Elecraft Support


[hidden email] wrote:

>Ok, confused here.  On page 28 of the Owners Manual it says to check off the
>items NOT installed.  If I have the SSB kit, which I do, it says to install them
>now.
>
>RP3 has some issues.. it says its a 10k resistor network and is supplied in the
>SSB kit.  The board shows it as an 8 pin inline part.  The SSB parts had all the
>parts BUT describes RP3 as a 2K 6 pin resistor network AND there is NO 10K
>inline pin resistor chip in the SSB bag to put in the front panel board.
>
>What goes in the RP3 slot on the Front panel board.  In the SSB manual it
>describes RP3 as a 10K 8 pin but on page 3 RP3 is a 2.0K 6 pin ???
>
>confused..
>_______________________________________________
>Elecraft mailing list
>Post to: [hidden email]
>You must be a subscriber to post to the list.
>Subscriber Info (Addr. Change, sub, unsub etc.):
> http://mailman.qth.net/mailman/listinfo/elecraft   
>
>Help: http://mailman.qth.net/subscribers.htm
>Elecraft web page: http://www.elecraft.com
>
>
>  
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com