JT-65A modes
Locked
 
|
A fellow Elecrafter gave me his number and i called him because i wasn't making any progress with the problem of keying the radio with the WSJT program. What it came down to was in the configuration table for WSJT. There is a place for "PTT" port and mine was set on 0. I suspected that might have something to do with it but had no idea what should be in there. Ken said his was 3, what a magical number! It worked for me as well. So now the radio goes into transmit mode as it should. End of one problem. I am using the Data A mode, USB, Mic-Line is set to ON, VOX Gain at 10, Antivox 000, TX delay 008 (min), PTT Key RTS-DTR Now what happens is that it transmitts the message i have selected and right about the 48 second mark it drops, then a few seconds later it keys up and starts resend the message again but stops when the clock hits 00 and goes into receive mode. If i was a kid this would be easy but being an old F*** its a bit more time consuming so i appreciate any all exibitions of patience. Larry W0OGH ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
|
|
> Now what happens is that it transmitts the message i have selected and right about the 48 second mark it drops, then a few seconds later it keys up and starts resend the message again but stops when the clock hits 00 and goes into receive mode. are you sure its resending the message or the CW ID try taking the ID off and see Rgds Simon ZL4PLM Check out more information on the world 50 MHz and Up : www.zl4plm.com > Date: Thu, 19 Jul 2012 19:35:00 -0400 > From: [hidden email] > To: [hidden email] > Subject: [Elecraft] JT-65A modes > > > A fellow Elecrafter gave me his number and i called him because i wasn't making any progress with the problem of keying the radio with the WSJT program. What it came down to was in the configuration table for WSJT. There is a place for "PTT" port and mine was set on 0. I suspected that might have something to do with it but had no idea what should be in there. Ken said his was 3, what a magical number! It worked for me as well. So now the radio goes into transmit mode as it should. End of one problem. > > I am using the Data A mode, USB, Mic-Line is set to ON, VOX Gain at 10, Antivox 000, TX delay 008 (min), PTT Key RTS-DTR > > Now what happens is that it transmitts the message i have selected and right about the 48 second mark it drops, then a few seconds later it keys up and starts resend the message again but stops when the clock hits 00 and goes into receive mode. > > If i was a kid this would be easy but being an old F*** its a bit more time consuming so i appreciate any all exibitions of patience. > > Larry > W0OGH > > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
|
|
In reply to this post by telegrapher
> I am using the Data A mode, USB, Mic-Line is set to ON, Mic+Line is not applicable in DATA A - don't know how you get and invalid configuration. > PTT Key RTS-DTR PTT/Key is only valid for the CAT port - if COM3 is normally your control connection from HRD, etc. that's fine but you would be better served to not tie up the CAT port for just PTT. > then a few seconds later it keys up and starts resend the message > again but stops when the clock hits 00 and goes into receive mode. Sounds like a CW ID but that's too long for JT65HF and I don't see any CW ID in either WSJT7 or WSJT9. 73, ... Joe, W4TV On 7/19/2012 7:35 PM, [hidden email] wrote: > > A fellow Elecrafter gave me his number and i called him because i wasn't making any progress with the problem of keying the radio with the WSJT program. What it came down to was in the configuration table for WSJT. There is a place for "PTT" port and mine was set on 0. I suspected that might have something to do with it but had no idea what should be in there. Ken said his was 3, what a magical number! It worked for me as well. So now the radio goes into transmit mode as it should. End of one problem. > > I am using the Data A mode, USB, Mic-Line is set to ON, VOX Gain at 10, Antivox 000, TX delay 008 (min), PTT Key RTS-DTR > > Now what happens is that it transmitts the message i have selected and right about the 48 second mark it drops, then a few seconds later it keys up and starts resend the message again but stops when the clock hits 00 and goes into receive mode. > > If i was a kid this would be easy but being an old F*** its a bit more time consuming so i appreciate any all exibitions of patience. > > Larry > W0OGH > > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
|
|
Check out more information on the world 50 MHz and Up : www.zl4plm.com > > Sounds like a CW ID but that's too long for JT65HF and I don't see > any CW ID in either WSJT7 or WSJT9. on the setup page ID interval - set it to 0 ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
|
|
In reply to this post by Joe Subich, W4TV-4
On 7/19/2012 5:40 PM, Joe Subich, W4TV wrote:
> Sounds like a CW ID but that's too long for JT65HF and I don't see > any CW ID in either WSJT7 or WSJT9. Both WSJT9 and JT65-HF have an optional setting to send a CW ID. With WSJT9 you choose a time interval, and it will ID at the end of a transmission. With JT65-HF you can set it to ID after sending free text. It sends CW as an audio tone, which modulates just like the digital data, and it produces normal CW on the air. 73, Jim K9YC ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
«
Return to [HAM]
|
1 view|%1 views
| Free forum by Nabble | Edit this page |