K2 dimensions

[Daniel Reynolds-2]

Do the K2 dimensions (7.8 x 8.2 x 2.9) include the knobs, rear BNC connectors,
and rubber feet?

Thanks,
Daniel AA0NI


_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Joe-aa4nn]

If you include the extremities plus finger dimple,
it is more like 10 inches front to back.


> Do the K2 dimensions (7.8 x 8.2 x 2.9) include the knobs, rear BNC
> connectors,
> and rubber feet?
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Don Nesbitt]

No - approximate height of mine with feet is 3 3/8 plus a "tad" - total
about 3 7/16 allowing for the screw heads - width almost exactly 8 "
(including screw heads) and (here is where it gets tricky) depth about 10
inches (+ or - depending on if you have finger dimple installed or not) from
farthest front protrusion to farthest rear protrusion (end of bnc's) - if
you have the KPA100, the SO-239 sticks out about as far as the BNC's - now
if you plug in the key plug, power poles ( if you have the KPA100), KIO2
connector, etc, etc, there is more measuring to do!

Bet that was more than you wanted to know!  -- 73 -- Don N4HH

----- Original Message -----
From: "Daniel Reynolds" <[hidden email]>
To: <[hidden email]>
Sent: Tuesday, March 28, 2006 9:49 AM
Subject: [Elecraft] K2 dimensions

> Do the K2 dimensions (7.8 x 8.2 x 2.9) include the knobs, rear BNC
> connectors,
> and rubber feet?
>
> Thanks,
> Daniel AA0NI
>
>
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
> http://mailman.qth.net/mailman/listinfo/elecraft
>
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.1.385 / Virus Database: 268.3.2/294 - Release Date: 3/27/2006
>
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Sverre Holm-2]

> -----Original Message-----
>
> No - approximate height of mine with feet is 3 3/8 plus a
> "tad" - total about 3 7/16 allowing for the screw heads -
> width almost exactly 8 " (including screw heads)

This is 20.3 cm by 8.7 cm. There are something like 5500 K2s out there now,
so if you stack them all together: 50 next to each other by 110 in height
then this is a width of 10.2 m by 9.6 m in height.

Sorry my head has been tuned to metric from the very beginning, but
converting back this is 33.3 by 31.4 feet. Quite a stack!

Congratulations to Elecraft, you must have done something right!

73

Sverre
LA3ZA
http://www.qslnet.de/la3za/
 


_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com