12345678 ... 66

	Topics (2297)	Replies	Last Post	Views
	K2 AGC and CAL HI LO value question by Jean-François | VA2S...	2	by Jean-François | VA2S...
	Alignement and Test part II - VCO Test not reading 8 to 10 MHZ range. by VA2EK	2	by VA2EK
	[K2] Safely running 100% key-down modes by K1FFX	4	by Bill Coleman-2
	K2 / KPA ALC problem. by Chris Kimball	19	by Don Wilhelm-4
	Audible thump sound when sending cw on K2 by Don Baucom	2	by Don Baucom
	Convert KAT 100-2 back to KAT 100-1 by Bob Whelan	0	by Bob Whelan
	k2 #7377 by haircutter@verizon.n...	3	by haircutter@verizon.n...
	[k2] Doc download not working for me, are there problems ? by ik1bxn	1	by Don Wilhelm-4
	[K2] PA ALC problem on CW by picmaster	4	by picmaster
	KPA100 problem with SWR bridge - High SWR by Stan AE7UT	1	by Stan AE7UT
	KNB2 - looking for experience with mods that made it effective by Stan AE7UT	7	by OE5CSP-Chris
	[K2] FS: KDSP2 for K2 -- price reduced by wd8rif	0	by wd8rif
	[K2] FS: KDSP2 module by wd8rif	1	by wd8rif
	Lo P on 10 and 12 meters by EMD	4	by EMD
	K2 net? by N2PD	1	by Ian Kahn, KM4IK
	K2 EXCESSIVE PREAMP NOISE? by N2PD	6	by Don Wilhelm-4
	KIO2 Problems by ted	1	by Don Wilhelm-4
	K2 100 shuts down immediately - need help by Stan AE7UT	4	by Don Wilhelm-4
	K2 adjusting L34 by N2PD	0	by N2PD
	K2 #7446 is alive and made my first QSO by Stan AE7UT	6	by Stan AE7UT
	KPA-100 pop from TX to RX by DaveVK	5	by DaveVK
	K2 - KAT2 receive 4.7v voltage out on U4 pin 1 and 7 by ChrisM	1	by Don Wilhelm-4
	[K2] N1MM Logger with KPA100 by K1FFX	4	by Don Wilhelm-4
	K2 almost deaf on 40 meters only by Stan AE7UT	3	by Stan AE7UT
	Low Tx power, and receive strength on 17meters only by k1-4 user	0	by k1-4 user
	K2 40m transmitter alignment: Low Current? by ChrisM	2	by ChrisM
	K2 Why MH2 mic seems dead by k7nhb	2	by Eugene Balinski
	K2 sn 4900-5000 - Upgrades needed? by iw7dmh	3	by iw7dmh
	For Sale Elecraft k3 & P3 AND Icom IC-7600 by ag6sh	14	by k6dgw
	Want to buy a KAF2 module by Stan AE7UT	0	by Stan AE7UT
	K2 Cosmetic Upgrade by Sverre Holm (LA3ZA)	1	by RobertG
	Rework eliminators by Stan AE7UT	10	by Edward R Cole
	Connector for K2 Mic. Config. header by Chris Kimball	2	by Chris Kimball
	K2 Audio Thumping & Shutdown Noise by K4GDR	1	by Don Wilhelm-4
	KAT100 project - removing the control board by Stan AE7UT	10	by Stan AE7UT

12345678 ... 66

Free forum by Nabble

Edit this page