K2 - no tone on TX
Locked
 
|
I did a lot of maintenance work on my K2 today. It required tearing it down
board by board. All work went well. I buttoned it up and hooked everything up. It is transmitting on CW but there is no tone, as in dah dit, just a slight clicking. It appears to be putting out appropriate poser levels but is not making a tine through the speaker or in the headphones if plugged in. I suspect something silly or simple. Any ideas????? Dohn N8EWY _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
Don and Jeff Kinzli had this discussion yesterday afternoon. You might
look though those email, labeled "K2 lost sidetone", Don supplied some suggestions there. David Wilburn [hidden email] Dohn wrote: > I did a lot of maintenance work on my K2 today. It required tearing it down > board by board. All work went well. I buttoned it up and hooked everything > up. It is transmitting on CW but there is no tone, as in dah dit, just a > slight clicking. It appears to be putting out appropriate poser levels but > is not making a tine through the speaker or in the headphones if plugged in. > > > > I suspect something silly or simple. Any ideas????? > > > > Dohn N8EWY > > _______________________________________________ > Elecraft mailing list > Post to: [hidden email] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
You were absolutely right. I even saved that post from Don because it
seemed like a good one for my own archive. That's pretty weird. I just saved it yesterday and needed it today. Go figure. Thanks so much. 73 Dohn N8EWY -----Original Message----- From: David Wilburn [mailto:[hidden email]] Sent: Saturday, February 17, 2007 9:04 PM To: Dohn Cc: [hidden email] Subject: Re: [Elecraft] K2 - no tone on TX Don and Jeff Kinzli had this discussion yesterday afternoon. You might look though those email, labeled "K2 lost sidetone", Don supplied some suggestions there. David Wilburn [hidden email] Dohn wrote: > I did a lot of maintenance work on my K2 today. It required tearing it down > board by board. All work went well. I buttoned it up and hooked everything > up. It is transmitting on CW but there is no tone, as in dah dit, just a > slight clicking. It appears to be putting out appropriate poser levels but > is not making a tine through the speaker or in the headphones if plugged in. > > > > I suspect something silly or simple. Any ideas????? > > > > Dohn N8EWY > > _______________________________________________ > Elecraft mailing list > Post to: [hidden email] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > -- No virus found in this incoming message. Checked by AVG Free Edition. Version: 7.1.412 / Virus Database: 268.18.1/690 - Release Date: 2/16/2007 _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
In reply to this post by n8ewy
There's a non-obvious switch in the software that is easy to hit when you
are doing things. It changes the source of your sidetone, i.e. which pin of the controller it's taken from. If that gets changed you lose your sidetone. Press MENU then select sidetone level (St L). Hold MENU to make that choice active, then tap DISPLAY to change the source. You should hear sidetone when you tap DISPLAY if that's the problem. Ron AC7AC -----Original Message----- From: [hidden email] [mailto:[hidden email]] On Behalf Of Dohn Sent: Saturday, February 17, 2007 5:43 PM To: [hidden email] Subject: [Elecraft] K2 - no tone on TX I did a lot of maintenance work on my K2 today. It required tearing it down board by board. All work went well. I buttoned it up and hooked everything up. It is transmitting on CW but there is no tone, as in dah dit, just a slight clicking. It appears to be putting out appropriate poser levels but is not making a tine through the speaker or in the headphones if plugged in. I suspect something silly or simple. Any ideas????? Dohn N8EWY _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
«
Return to Elecraft
|
1 view|%1 views
| Free forum by Nabble | Edit this page |