Elecraft

K3 Beta Firmware Release, Rev. 2.22

Classic

List

Threaded

8 messages Options

wayne burdick

K3 Beta Firmware Release, Rev. 2.22

Administrator

K3 beta-test firmware revision 2.22 is now available. Details appear
below.

For instructions on how to load beta firmware, please see:

http://www.elecraft.com/K3/k3_software.htm

73,
Wayne
N6KR

* * *

MCU 2.22 / DSP 1.88, 7-28-08

- CHANNEL SCAN no longer locks out small encoders (during scan or after
stopping it). (Channel scanning is most often used on 60 meters; refer
to the owner's manual for details.)

- USER-DEFINED “NORM” VALUES are now referred to as "NORM1/2" rather
than "ALT1/2" to avoid confusion with the “ALT” switch (alternate
mode).

- FLASH MEMORY INITIALIZATION corrected to prevent spurious “FPF LOAD
PENDING” messages. If this message does appear unexpectedly, tap any
switch to see the flash read exception code, e.g. “FPF 1”. Report this
to customer support.

---

http://www.elecraft.com

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

Guy, K2AV

Re: K3 Beta Firmware Release, Rev. 2.22

I'm still showing 2.19 at the beta site. What am I doing wrong?

<quote author="wayne burdick">
K3 beta-test firmware revision 2.22 is now available. Details appear
below.

For instructions on how to load beta firmware, please see:

http://www.elecraft.com/K3/k3_software.htm

73,
Wayne
N6KR

* * *

MCU 2.22 / DSP 1.88, 7-28-08

...snip...

Augie "Gus" Hansen

Re: K3 Beta Firmware Release, Rev. 2.22

Guy, K2AV wrote:
> I'm still showing 2.19 at the beta site. What am I doing wrong?
>

Beta version 2.22 came up fine here. Most likely your browser is using a
previously cached page. Try forcing your browser to load the page from
the Elecraft web site.

Gus Hansen
KB0YH

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

KK7P

Re: K3 Beta Firmware Release, Rev. 2.22

In reply to this post by Guy, K2AV

> I'm still showing 2.19 at the beta site. What am I doing wrong?

Refreshing your browser will usually fix this. You might have to not be
using the web site in frames mode to make this work (select no frames
from the box on the left).

73,

Lyle KK7P

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

Iain MacDonnell - N6ML

Re: K3 Beta Firmware Release, Rev. 2.22

Lyle Johnson wrote on 07/29/08 17:30:
>> I'm still showing 2.19 at the beta site. What am I doing wrong?
>
> Refreshing your browser will usually fix this. You might have to not be
> using the web site in frames mode to make this work (select no frames
> from the box on the left).

Or you could right-click on the frame in question and choose "This
Frame" -> "Reload Frame", or "Refresh" (depending on your browser).

~Iain

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

Guy, K2AV

Re: K3 Beta Firmware Release, Rev. 2.22

Guess it was storing the FTP layout in cache. My bad. I hate rookie
mistakes...

73, Guy.

----- Original Message -----
From: "Iain MacDonnell - K6IAM" <[hidden email]>
To: "Lyle Johnson" <[hidden email]>
Cc: "Guy, K2AV" <[hidden email]>; <[hidden email]>
Sent: Tuesday, July 29, 2008 8:35 PM
Subject: Re: [Elecraft] K3 Beta Firmware Release, Rev. 2.22

Lyle Johnson wrote on 07/29/08 17:30:
>> I'm still showing 2.19 at the beta site. What am I doing wrong?
>
> Refreshing your browser will usually fix this. You might have to not be
> using the web site in frames mode to make this work (select no frames
> from the box on the left).

Or you could right-click on the frame in question and choose "This
Frame" -> "Reload Frame", or "Refresh" (depending on your browser).

~Iain

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

Dick Dievendorff

Re: K3 Beta Firmware Release, Rev. 2.22

In reply to this post by wayne burdick

Try clicking the "refresh" button on your browser, or purge your internet cache. You're probably looking at a cached copy of the list of files in the directory.

Dick, K6KR

-------------- Original message --------------
From: "Guy, K2AV" <[hidden email]>

>
> I'm still showing 2.19 at the beta site. What am I doing wrong?
>
>
> K3 beta-test firmware revision 2.22 is now available. Details appear
> below.
>
> For instructions on how to load beta firmware, please see:
>
> http://www.elecraft.com/K3/k3_software.htm
>
> 73,
> Wayne
> N6KR
>
> * * *
>
> MCU 2.22 / DSP 1.88, 7-28-08
>
> ...snip...
> --
> View this message in context:
> http://n2.nabble.com/K3-Beta-Firmware-Release%2C-Rev.-2.22-tp640807p640854.html
> Sent from the Elecraft mailing list archive at Nabble.com.
>
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
> http://mailman.qth.net/mailman/listinfo/elecraft
>
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

Steef PA2A

Re: K3 Beta Firmware Release, Rev. 2.22

In reply to this post by Iain MacDonnell - N6ML

Press CONTROL-F5 to reload bypassing the internet cache files.

73 's Steef PA2A

----- Original Message -----
From: "Iain MacDonnell - K6IAM" <[hidden email]>
To: "Lyle Johnson" <[hidden email]>
Cc: <[hidden email]>; "Guy, K2AV" <[hidden email]>
Sent: Wednesday, July 30, 2008 2:35 AM
Subject: Re: [Elecraft] K3 Beta Firmware Release, Rev. 2.22

>
>
> Lyle Johnson wrote on 07/29/08 17:30:
>>> I'm still showing 2.19 at the beta site. What am I doing wrong?
>>
>> Refreshing your browser will usually fix this. You might have to not be
>> using the web site in frames mode to make this work (select no frames
>> from the box on the left).
>
> Or you could right-click on the frame in question and choose "This
> Frame" -> "Reload Frame", or "Refresh" (depending on your browser).
>
> ~Iain
>
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
> http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com