Elecraft › [K3]

K3 MCU LD

Classic

List

Threaded

3 messages Options

hf4me

K3 MCU LD

I had made several JT65 contacts and a phone contact just prior to this
problem.

K3 hung up (became constant errors appearing to be communications problems)
during load of new code from non-updated Utility Program. Went to website
and downloaded new Utility and re-downloaded code. K3 was now in MCU LD
mode. Utility indicated during port test that the K3 needed a MCU LD. This
only happened once. After that it was just trying different baud rates on
the comm port. Disconnected PC to P3 cable at P3 and connected directly to
K3. No change. Removed that cable and used the cable had gone from the P3
to the K3. No change. Used another PC with a real Comm port and downloaded
the K3 Utility to it and tried it direct. That did not work either.
Different PC, different cable, new loads of Utility and K3 code to each PC
each direct from the Elecreaft site. The only common piece here is the K3.

The K3 initially had to have power unplugged as it was totally froze up
after the initial incident. When powered on, it came up in MCU LD mode on
its own. That is the only time the Utility program said it needed MCU LD.
The PCs had been rebooted numerous times during this procedure to insure
there wasn't something being assumed by the PC OS or the Utility program.
All future times it simply could not communicate, repeatedly trying
descending baud rates.

Looking at the Utility help files on force loading the MCU, it says to leave
the K3 without power connected for longer than a few seconds. This was done
for a 35 minute period, no change. Power on was done by procedure of
holding the power switch in until the transmit light starts blinking and the
darkened panel shows MCU LD.

I also removed the top cover and removed and reinstalled the KIO3 bd and the
KXV3 bd. No loose connections.

I CANNOT talk to it. Anybody with any ideas, please respond.

Thanks es 73, de Jim KG0KP

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Don Wilhelm-4

Re: K3 MCU LD

Jim,

This comes up continuously.

If something interrupts a firmware load, you will end up in the
condition stated. I could say "RTFM" or read the prior posts that ask
the same question -- BUT ---

The cure is to read *carefully* the instructions in either the manual or
the K3 Utility "to force a firmware load".

Shortcuts do not work - follow the instructions carefully from beginning
to end, and re-boot the computer with each attempt.

If K3 Utility cannot establish communications, you may have a problem
with your serial port - if you are using a USB to serial adapter, try
another one. Some adapters are good, while others are "flaky" - make no
assumptions, but do try a different adapter if necessary. The adapters
that work use the FTDI chipset. Make certain you have the latest
drivers loaded. (a real serial port is the best solution)..

73,
Don W3FPR

On 7/8/2012 11:46 PM, Jim Miller KG0KP wrote:

> I had made several JT65 contacts and a phone contact just prior to this
> problem.
>
> K3 hung up (became constant errors appearing to be communications problems)
> during load of new code from non-updated Utility Program. Went to website
> and downloaded new Utility and re-downloaded code. K3 was now in MCU LD
> mode. Utility indicated during port test that the K3 needed a MCU LD. This
> only happened once. After that it was just trying different baud rates on
> the comm port. Disconnected PC to P3 cable at P3 and connected directly to
> K3. No change. Removed that cable and used the cable had gone from the P3
> to the K3. No change. Used another PC with a real Comm port and downloaded
> the K3 Utility to it and tried it direct. That did not work either.
> Different PC, different cable, new loads of Utility and K3 code to each PC
> each direct from the Elecreaft site. The only common piece here is the K3.
>
> The K3 initially had to have power unplugged as it was totally froze up
> after the initial incident. When powered on, it came up in MCU LD mode on
> its own. That is the only time the Utility program said it needed MCU LD.
> The PCs had been rebooted numerous times during this procedure to insure
> there wasn't something being assumed by the PC OS or the Utility program.
> All future times it simply could not communicate, repeatedly trying
> descending baud rates.
>
> Looking at the Utility help files on force loading the MCU, it says to leave
> the K3 without power connected for longer than a few seconds. This was done
> for a 35 minute period, no change. Power on was done by procedure of
> holding the power switch in until the transmit light starts blinking and the
> darkened panel shows MCU LD.
>
> I also removed the top cover and removed and reinstalled the KIO3 bd and the
> KXV3 bd. No loose connections.
>
> I CANNOT talk to it. Anybody with any ideas, please respond.
>
> Thanks es 73, de Jim KG0KP
>
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Dick Dievendorff

Re: K3 MCU LD

In reply to this post by hf4me

Please follow the steps in K3 Utility Help, Troubleshooting MCU Load failure.

Dick, K6KR

Sent from my iPad

On Jul 8, 2012, at 8:46 PM, "Jim Miller KG0KP" <[hidden email]> wrote: