KPA1500 fan mod done - MUCH better
Locked
 
|
Hi All,
Received the new LED board for my KPA1500 power supply. Easy to swap out, six plugs and two screws. You can move one plug at a time to the new board so there is no chance of screwing anything up. To put the screws back in I suggest a Phillips screwdriver with magnetic tip. It took more time to remove the 16 screws from the top cover than to swap the board. THANK YOU Elecraft! 73 Dave wo2x ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
Re: KPA1500 fan mod done - MUCH better
|
|
You didn’t happen to notice the value of the changed resistor did you? The fan resistor is the big one.
Ken K6MR From: [hidden email]<mailto:[hidden email]> Sent: Thursday, June 4, 2020 17:00 To: [hidden email]<mailto:[hidden email]> Subject: [Elecraft] KPA1500 fan mod done - MUCH better Hi All, Received the new LED board for my KPA1500 power supply. Easy to swap out, six plugs and two screws. You can move one plug at a time to the new board so there is no chance of screwing anything up. To put the screws back in I suggest a Phillips screwdriver with magnetic tip. It took more time to remove the 16 screws from the top cover than to swap the board. THANK YOU Elecraft! 73 Dave wo2x ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
Re: KPA1500 fan mod done - MUCH better
|
|
In reply to this post by Dave wo2x
I had completely forgotten that I did this mod, and the two resistors mod.
That, and the piece of grit or whatever that was stuck in one of the PSU fans making it scream like a banshee, took the KPA1500 PSU fan noise from being intolerable to unnoticable. Good times! Ain't it grand! 73 Eric WD6DBM On Thu, Jun 4, 2020, 4:59 PM <[hidden email]> wrote: > Hi All, > > > > Received the new LED board for my KPA1500 power supply. Easy to swap out, > six plugs and two screws. You can move one plug at a time to the new board > so there is no chance of screwing anything up. To put the screws back in I > suggest a Phillips screwdriver with magnetic tip. It took more time to > remove the 16 screws from the top cover than to swap the board. > > > > THANK YOU Elecraft! > > > > 73 > > Dave wo2x > > > > > > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [hidden email] > Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
Yeah PSU fan noise is on par with the fans in the Flex 6700 now. PC is almost completely silent. Thinking of locating the amp, radio, and 4O3A 2x8 antenna switch in my garage in a half height server cabinet. Then I could hear myself think, but maybe I don’t want to hear myself ;-)
The two chip resistor mod on filter board was fun. I have experience with surface mount rework so no big deal. One resistor was the size of “16” onthe date on a penny (2016). Other mods - they installed zener diodes tonthe gates on the LDMOS devices to protect against overdrive. That is one thing the LDMOS devices do not like. Mybamp uses a pair of NXP 1K50H devices which I feel are more rugged than BLF188 and 189s. I heard early amps used the 188s but no proof of that. Have fun! 73 Dave Sent from my iPad > On Jun 5, 2020, at 1:10 AM, Eric Norris <[hidden email]> wrote: > > > I had completely forgotten that I did this mod, and the two resistors mod. That, and the piece of grit or whatever that was stuck in one of the PSU fans making it scream like a banshee, took the KPA1500 PSU fan noise from being intolerable to unnoticable. > > Good times! Ain't it grand! > > 73 Eric WD6DBM > >> On Thu, Jun 4, 2020, 4:59 PM <[hidden email]> wrote: >> Hi All, >> >> >> >> Received the new LED board for my KPA1500 power supply. Easy to swap out, >> six plugs and two screws. You can move one plug at a time to the new board >> so there is no chance of screwing anything up. To put the screws back in I >> suggest a Phillips screwdriver with magnetic tip. It took more time to >> remove the 16 screws from the top cover than to swap the board. >> >> >> >> THANK YOU Elecraft! >> >> >> >> 73 >> >> Dave wo2x >> >> >> >> >> >> >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[hidden email] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to [hidden email] Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
Dave,
So, are these mods documented somewhere on the Elecraft site? I have been unable to locate them. Further, I can't even get Elecraft to respond about when they will provide schematics for the KPA1500. Thanks Mike K7PI -----Original Message----- From: [hidden email] <[hidden email]> On Behalf Of Dave Sent: Thursday, June 4, 2020 22:41 To: Eric Norris <[hidden email]> Cc: elecraft@mailman qth. net <[hidden email]> Subject: Re: [Elecraft] KPA1500 fan mod done - MUCH better Yeah PSU fan noise is on par with the fans in the Flex 6700 now. PC is almost completely silent. Thinking of locating the amp, radio, and 4O3A 2x8 antenna switch in my garage in a half height server cabinet. Then I could hear myself think, but maybe I don’t want to hear myself ;-) The two chip resistor mod on filter board was fun. I have experience with surface mount rework so no big deal. One resistor was the size of “16” onthe date on a penny (2016). Other mods - they installed zener diodes tonthe gates on the LDMOS devices to protect against overdrive. That is one thing the LDMOS devices do not like. Mybamp uses a pair of NXP 1K50H devices which I feel are more rugged than BLF188 and 189s. I heard early amps used the 188s but no proof of that. Have fun! 73 Dave Sent from my iPad > On Jun 5, 2020, at 1:10 AM, Eric Norris <[hidden email]> wrote: > > > I had completely forgotten that I did this mod, and the two resistors mod. That, and the piece of grit or whatever that was stuck in one of the PSU fans making it scream like a banshee, took the KPA1500 PSU fan noise from being intolerable to unnoticable. > > Good times! Ain't it grand! > > 73 Eric WD6DBM > >> On Thu, Jun 4, 2020, 4:59 PM <[hidden email]> wrote: >> Hi All, >> >> >> >> Received the new LED board for my KPA1500 power supply. Easy to swap >> out, six plugs and two screws. You can move one plug at a time to the >> new board so there is no chance of screwing anything up. To put the >> screws back in I suggest a Phillips screwdriver with magnetic tip. It >> took more time to remove the 16 screws from the top cover than to swap the board. >> >> >> >> THANK YOU Elecraft! >> >> >> >> 73 >> >> Dave wo2x >> >> >> >> >> >> >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[hidden email] >> >> This list hosted by: http://www.qsl.net Please help support this >> email list: http://www.qsl.net/donate.html Message delivered to >> [hidden email] Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
«
Return to Elecraft
|
1 view|%1 views
| Free forum by Nabble | Edit this page |