KX3 2M module install -- HELP

[Grant Youngman-2]

Before I call tech support, thought I’d try here.

Just installed in the 2M module in my KX3. I’m on the latest firmware rev.  Gone over the setup instructions several times, and the parameters are all set properly — enabled, 50 Mhz IF, in the band map, etc.

When I go to the 2M band, the display comes up 122.000.00  ?????

Anyone have an idea?

Thanks ...
Grant NQ5T
K3 #2091, KX3 #8342



______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Grant Youngman-2]

Never mind …

Apparently it was just some garbage in VFO A.  VFO B was on 144.00 where it should have been.  A swap and copy of VFOs fixed the problem.

> On Feb 3, 2017, at 3:37 PM, GRANT YOUNGMAN <[hidden email]> wrote:
>
> Before I call tech support, thought I’d try here.
>
> Just installed in the 2M module in my KX3. I’m on the latest firmware rev.  Gone over the setup instructions several times, and the parameters are all set properly — enabled, 50 Mhz IF, in the band map, etc.
>
> When I go to the 2M band, the display comes up 122.000.00  ?????
>
> Anyone have an idea?
>
> Thanks ...
> Grant NQ5T
> K3 #2091, KX3 #8342
>
>
>

Grant NQ5T
K3 #2091, KX3 #8342



______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Bob N3MNT]

Have you shut down the radio and restarted it?

[Grant Youngman-2]

Yes, several times.  Just looks like a minor glitch.  See my note below.

Thanks … Grant NQ5T

> On Feb 3, 2017, at 3:51 PM, GRANT YOUNGMAN <[hidden email]> wrote:
>
> Never mind …
>
> Apparently it was just some garbage in VFO A.  VFO B was on 144.00 where it should have been.  A swap and copy of VFOs fixed the problem.
>
>
>> On Feb 3, 2017, at 3:37 PM, GRANT YOUNGMAN <[hidden email]> wrote:
>>
>> Before I call tech support, thought I’d try here.
>>
>> Just installed in the 2M module in my KX3. I’m on the latest firmware rev.  Gone over the setup instructions several times, and the parameters are all set properly — enabled, 50 Mhz IF, in the band map, etc.
>>
>> When I go to the 2M band, the display comes up 122.000.00  ?????
>>
>> Anyone have an idea?
>>
>> Thanks ...
>> Grant NQ5T
>> K3 #2091, KX3 #8342
>>
>>
>>
>
> Grant NQ5T
> K3 #2091, KX3 #8342
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]