KX3 - Mode switch skips AM
Locked
 
|
Hello,
Tapping MODE switch on my KX3 with MCU 02.90, most latest firmware, switches mode from SSB -> CW -> FM, then back to SSB. It does skips AM. I have not switched to AM for long time. I think I was able to select AM by tapping MODE before. I went through KX3 Owner’s Manual to look for any configuration to skip any specific mode, but found none. Sending “MD5;” from KX3 utility software switches KX3 to AM mode. So MPU is OK on selecting a mode except switching the mode by MODE switch. I restored my KX3 configuration backed up almost 6 months ago, but the symptom is same. Then I reloaded the latest firmware to my KX3, but the same result. Have anyone experienced the similar problem? Your though on any possible cause are welcome. 73 de JH3SIF, Keith ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
Correction as below;
Tapping MODE switch on my KX3 with MCU 02.90, most latest firmware, switches mode from SSB -> CW -> FM -> FM, then back to SSB. It does skips AM. 73 de JH3SIF, Keith > 2019/01/14 7:37、Keith Onishi <[hidden email]>のメール: > > Hello, > > Tapping MODE switch on my KX3 with MCU 02.90, most latest firmware, switches mode from SSB -> CW -> FM, then back to SSB. It does skips AM. > I have not switched to AM for long time. I think I was able to select AM by tapping MODE before. > I went through KX3 Owner’s Manual to look for any configuration to skip any specific mode, but found none. > Sending “MD5;” from KX3 utility software switches KX3 to AM mode. So MPU is OK on selecting a mode except switching the mode by MODE switch. > I restored my KX3 configuration backed up almost 6 months ago, but the symptom is same. Then I reloaded the latest firmware to my KX3, but the same result. > > Have anyone experienced the similar problem? > Your though on any possible cause are welcome. > > 73 de JH3SIF, Keith > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [hidden email] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
In reply to this post by jh3sif
Keith,
Go to the menu and make sure AM MODE is turned ON. 73, Don W3FPR On 1/13/2019 5:37 PM, Keith Onishi wrote: > Hello, > > Tapping MODE switch on my KX3 with MCU 02.90, most latest firmware, switches mode from SSB -> CW -> FM, then back to SSB. It does skips AM. > I have not switched to AM for long time. I think I was able to select AM by tapping MODE before. > I went through KX3 Owner’s Manual to look for any configuration to skip any specific mode, but found none. > Sending “MD5;” from KX3 utility software switches KX3 to AM mode. So MPU is OK on selecting a mode except switching the mode by MODE switch. > I restored my KX3 configuration backed up almost 6 months ago, but the symptom is same. Then I reloaded the latest firmware to my KX3, but the same result. > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
Many thanks, Don.
Now AM mode came back. But I do not remember when I set AM MODE OFF. 73 de JH3SIF, Keith > 2019/01/14 7:53、Don Wilhelm <[hidden email]>のメール: > > Keith, > > Go to the menu and make sure AM MODE is turned ON. > > 73, > Don W3FPR > > On 1/13/2019 5:37 PM, Keith Onishi wrote: >> Hello, >> Tapping MODE switch on my KX3 with MCU 02.90, most latest firmware, switches mode from SSB -> CW -> FM, then back to SSB. It does skips AM. >> I have not switched to AM for long time. I think I was able to select AM by tapping MODE before. >> I went through KX3 Owner’s Manual to look for any configuration to skip any specific mode, but found none. >> Sending “MD5;” from KX3 utility software switches KX3 to AM mode. So MPU is OK on selecting a mode except switching the mode by MODE switch. >> I restored my KX3 configuration backed up almost 6 months ago, but the symptom is same. Then I reloaded the latest firmware to my KX3, but the same result. ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
In reply to this post by jh3sif
Go to MENU and AM, turn it on?
Chuck Jack KE9UW Sent from my iPhone, cjack > On Jan 13, 2019, at 4:48 PM, Keith Onishi <[hidden email]> wrote: > > Correction as below; > > Tapping MODE switch on my KX3 with MCU 02.90, most latest firmware, switches mode from SSB -> CW -> FM -> FM, then back to SSB. It does skips AM. > > 73 de JH3SIF, Keith > >> 2019/01/14 7:37、Keith Onishi <[hidden email]>のメール: >> >> Hello, >> >> Tapping MODE switch on my KX3 with MCU 02.90, most latest firmware, switches mode from SSB -> CW -> FM, then back to SSB. It does skips AM. >> I have not switched to AM for long time. I think I was able to select AM by tapping MODE before. >> I went through KX3 Owner’s Manual to look for any configuration to skip any specific mode, but found none. >> Sending “MD5;” from KX3 utility software switches KX3 to AM mode. So MPU is OK on selecting a mode except switching the mode by MODE switch. >> I restored my KX3 configuration backed up almost 6 months ago, but the symptom is same. Then I reloaded the latest firmware to my KX3, but the same result. >> >> Have anyone experienced the similar problem? >> Your though on any possible cause are welcome. >> >> 73 de JH3SIF, Keith >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[hidden email] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to [hidden email] > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [hidden email] Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email]
Chuck, KE9UW
|
«
Return to Elecraft
|
1 view|%1 views
| Free forum by Nabble | Edit this page |