P3 Config Question

[Ferris Jennings]

Hi again -

 

I'm configuring my new P3, and have one big question: is there a way to make
"global changes".

 

To expand:

.         I set up 20 meters to show S units (LvL Mode=S Units); a Ref Lvl
from S0 to S9; Average = 5; Span = 20 khz, and apply that all to FN1

.         I then set up 20 meters to show S units (LvL Mode=S Units); a Ref
Lvl from S0 to S9; Average = 5; Span = 100 khz, and apply that all to FN2

 

That all works perfectly, and toggles between FN1 and FN2 is great.

 

But, when I go to any other band:

.         FN1 and FN2 toggle correctly between 20 khz and 100 khz, the
screen still displays S units; and the Average remains at 5.

.         But, on all bands except 20, where I configured the P3 , Ref Lvl
is way off, with S5 displayed at the bottom with +30 at the top of the
screen.

 

Desired State: What I would like is for the P3 display to appear the same on
all bands. So, is there a way to apply configuration changes globally to all
bands, or do I have to manually set Ref Lvl on each band?

 

Thanks

-Ferris NB6T-

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Don Wilhelm-4]

Ferris,

Many settings are per band - because what works fine on one band does
not work well for all bands.  There are other settings that are global.
I believe those settings you have cited are per band.  Set them for the
optimum on each band.

73,
Don W3FPR


On 12/26/2015 6:03 PM, Ferris Jennings wrote:

> Hi again -
>
>  
>
> I'm configuring my new P3, and have one big question: is there a way to make
> "global changes".
>
>  
>
> To expand:
>
> .         I set up 20 meters to show S units (LvL Mode=S Units); a Ref Lvl
> from S0 to S9; Average = 5; Span = 20 khz, and apply that all to FN1
>
> .         I then set up 20 meters to show S units (LvL Mode=S Units); a Ref
> Lvl from S0 to S9; Average = 5; Span = 100 khz, and apply that all to FN2
>
>  
>
> That all works perfectly, and toggles between FN1 and FN2 is great.
>
>  
>
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[k6dgw]

Short answer" No.  That said, you really want the long answer :-)

A great number of the P3 settings, like a K3, are on a per band basis.
Change the band, and it remembers the settings for that band.  In the
P3, much of this is because what works best on one band may not work all
that well on another.

The 8 programmable function keys aren't enough for a selection of
various options [like 2 SPAN's] and other parameters for each band.
Everyone runs it different:  For me, globally:

Always fixed-tune mode
Full-screen shift
Spectrum Avg = max
WF mode = monochrome
WF Avg = min
FN1 = 200 KHz span
FN2 = 100 KHz span
FN3 = 25 KHz span
FN4 = 4 KHz span
Amplitude scale = dBm

I've still got 4 unused FN keys. :-)

I use full-screen shift [the whole next span when I tune off either end]

I use monochrome WF because I don't have any color vision, however
several guest ops whose color vision is normal note that they can spot
weaker signals in mono than they can with the color display.  I'd
recommend you try both.

REF LVL:  The reference level will change from band to band and from
time to time on the same band.  It is a reflection of reality ... that's
what is really happening on the band, baseline noise [and noise
characteristics for that matter] change with time, and we normally like
the noise at the baseline.

Monitoring signals on the bands, the spectrum amplitude will NOT reflect
the S-Meter.  You can calibrate it with a signal generator of course,
but with max averaging in the spectrum, it won't directly,
quantitatively follow the S-Meter.  That too is normal.

I bought my P3 as a toy never guessing that it would end up being what I
look at while operating.

73,

Fred K6DGW
- Northern California Contest Club
- CU in the Cal QSO Party 1-2 Oct 2016
- www.cqp.org

On 12/26/2015 3:03 PM, Ferris Jennings wrote:

> I'm configuring my new P3, and have one big question: is there a way to make
> "global changes".

> To expand:
>
> .         I set up 20 meters to show S units (LvL Mode=S Units); a Ref Lvl
> from S0 to S9; Average = 5; Span = 20 khz, and apply that all to FN1
>
> .         I then set up 20 meters to show S units (LvL Mode=S Units); a Ref
> Lvl from S0 to S9; Average = 5; Span = 100 khz, and apply that all to FN2

> That all works perfectly, and toggles between FN1 and FN2 is great.

> But, when I go to any other band:
>
> .         FN1 and FN2 toggle correctly between 20 khz and 100 khz, the
> screen still displays S units; and the Average remains at 5.
>
> .         But, on all bands except 20, where I configured the P3 , Ref Lvl
> is way off, with S5 displayed at the bottom with +30 at the top of the
> screen.

> Desired State: What I would like is for the P3 display to appear the same on
> all bands. So, is there a way to apply configuration changes globally to all
> bands, or do I have to manually set Ref Lvl on each band?

> Thanks
>
> -Ferris NB6T-

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]