Elecraft

PR6 Preamplifier Power Plug 'P1'?

Classic

List

Threaded

7 messages Options

Jeffrey Maass

PR6 Preamplifier Power Plug 'P1'?

What is the manufacturer / type of the 'P1' plug required to provide power
to the PR6 preamplifier?

I cannot find any note in the manual or in previous posts to this reflector.

Thanks / 73,

Jeff K8ND

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

Nr4c

Re: PR6 Preamplifier Power Plug 'P1'?

I'd bet on coaxial power connector as used on other Elecraft gear. A 5 X 2.1 mm.

Sent from my iPhone
...nr4c. bill

> On Jun 3, 2017, at 10:22 PM, Jeffrey Maass <[hidden email]> wrote:
>
> What is the manufacturer / type of the 'P1' plug required to provide power
> to the PR6 preamplifier?
>
>
>
> I cannot find any note in the manual or in previous posts to this reflector.
>
>
>
> Thanks / 73,
>
> Jeff K8ND
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

Nr4c

Re: PR6 Preamplifier Power Plug 'P1'?

In reply to this post by Jeffrey Maass

Sorry. Don't have PR6. Disregard previous answer.

This looks like a typical .1 center. Single row female header. Should find on Mouser, Digikey or eBay. Also try Amazon.

Sent from my iPhone
...nr4c. bill

Jim AB3CV

Re: PR6 Preamplifier Power Plug 'P1'?

or a hobby shop that sells remote control accessories. this is typically
used to connect to servos.

jim ab3cv

On Sun, Jun 4, 2017 at 10:28 AM, Nr4c <[hidden email]> wrote:

> Sorry. Don't have PR6. Disregard previous answer.
>
> This looks like a typical .1 center. Single row female header. Should find
> on Mouser, Digikey or eBay. Also try Amazon.
>
> Sent from my iPhone
> ...nr4c. bill
>
>
> > On Jun 3, 2017, at 10:22 PM, Jeffrey Maass <[hidden email]> wrote:
> >
> > What is the manufacturer / type of the 'P1' plug required to provide
> power
> > to the PR6 preamplifier?
> >
> >
> >
> > I cannot find any note in the manual or in previous posts to this
> reflector.
> >
> >
> >
> > Thanks / 73,
> >
> > Jeff K8ND
> >
> > ______________________________________________________________
> > Elecraft mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:[hidden email]
> >
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> > Message delivered to [hidden email]
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]
>

Joe Subich, W4TV-4

Re: PR6 Preamplifier Power Plug 'P1'?

In reply to this post by Nr4c

P1 is a three pin 0.1" spacing PC "Header" type plug (rectangular body -
no lip). The plug housing is 0.30" W x 0.10 T x 0.60" L.

I do not know the manufacturer/part number.

73,

... Joe, W4TV

On 6/4/2017 10:07 AM, Nr4c wrote:

> I'd bet on coaxial power connector as used on other Elecraft gear. A 5 X 2.1 mm.
>
>
>
> Sent from my iPhone
> ...nr4c. bill
>
>
>> On Jun 3, 2017, at 10:22 PM, Jeffrey Maass <[hidden email]> wrote:
>>
>> What is the manufacturer / type of the 'P1' plug required to provide power
>> to the PR6 preamplifier?
>>
>>
>>
>> I cannot find any note in the manual or in previous posts to this reflector.
>>
>>
>>
>> Thanks / 73,
>>
>> Jeff K8ND
>>
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:[hidden email]
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to [hidden email]
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]
>

Nr4c

Re: PR6 Preamplifier Power Plug 'P1'?

In reply to this post by Jim AB3CV

Right!!!

Sent from my iPhone
...nr4c. bill

> On Jun 4, 2017, at 10:36 AM, Jim Miller <[hidden email]> wrote:
>
> or a hobby shop that sells remote control accessories. this is typically used to connect to servos.
>
> jim ab3cv
>
>> On Sun, Jun 4, 2017 at 10:28 AM, Nr4c <[hidden email]> wrote:
>> Sorry. Don't have PR6. Disregard previous answer.
>>
>> This looks like a typical .1 center. Single row female header. Should find on Mouser, Digikey or eBay. Also try Amazon.
>>
>> Sent from my iPhone
>> ...nr4c. bill
>>
>>
>> > On Jun 3, 2017, at 10:22 PM, Jeffrey Maass <[hidden email]> wrote:
>> >
>> > What is the manufacturer / type of the 'P1' plug required to provide power
>> > to the PR6 preamplifier?
>> >
>> >
>> >
>> > I cannot find any note in the manual or in previous posts to this reflector.
>> >
>> >
>> >
>> > Thanks / 73,
>> >
>> > Jeff K8ND
>> >
>> > ______________________________________________________________
>> > Elecraft mailing list
>> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> > Help: http://mailman.qth.net/mmfaq.htm
>> > Post: mailto:[hidden email]
>> >
>> > This list hosted by: http://www.qsl.net
>> > Please help support this email list: http://www.qsl.net/donate.html
>> > Message delivered to [hidden email]
>>
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:[hidden email]
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to [hidden email]
>

Ed K1EP

Re: PR6 Preamplifier Power Plug 'P1'?

In reply to this post by Jeffrey Maass

Go find an old junk computer, open it up and cut out one of the many three
pin motherboard header cables. Now you have a cable and connector!

On Jun 3, 2017 10:24 PM, "Jeffrey Maass" <[hidden email]> wrote:

What is the manufacturer / type of the 'P1' plug required to provide power
to the PR6 preamplifier?

I cannot find any note in the manual or in previous posts to this reflector.

Thanks / 73,

Jeff K8ND

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]