Please test KPA500 rev. 1.38 if you get a chance

[wayne burdick]

Hi all,

We updated the KPA500 beta firmware to revision 1.38 yesterday (from 1.37). The change was minor, pertaining to initial conditions when the KPA500 is used at remote locations.

If you get a chance, please load rev. 1.38 and verify that it is working well for all normal operation. Once we see a few more positive reports, we'll be going to production status on the K3, KPA500, and KAT500 beta firmware releases.

If you haven't already loaded K3 rev 4.83 and KAT500 rev 1.58, I'd encourage you to do these updates as well. The difference between the new firmware and previous production releases is pretty dramatic, as reported by beta testers over the past several days.

73,
Wayne
N6KR

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Don Nesbitt-2]

Loaded 1.38 and checked - no surprises in normal operation with K3 & KAT500 all appropriately cabled together.  73 es gud dxing -- Don N4HH


________________________________
 From: Wayne Burdick <[hidden email]>
To: Elecraft Reflector <[hidden email]>
Cc: "[hidden email]" <[hidden email]>
Sent: Tuesday, February 18, 2014 11:45 AM
Subject: [Elecraft_K3] Please test KPA500 rev. 1.38 if you get a chance
 


 
Hi all,

We updated the KPA500 beta firmware to revision 1.38 yesterday (from 1.37). The change was minor, pertaining to initial conditions when the KPA500 is used at remote locations.

If you get a chance, please load rev. 1.38 and verify that it is working well for all normal operation. Once we see a few more positive reports, we'll be going to production status on the K3, KPA500, and KAT500 beta firmware releases.

If you haven't already loaded K3 rev 4.83 and KAT500 rev 1.58, I'd encourage you to do these updates as well. The difference between the new firmware and previous production releases is pretty dramatic, as reported by beta testers over the past several days.

73,
Wayne
N6KR


__._,_.___
Reply via web post  Reply to sender   Reply to group   Start a New Topic  Messages in this topic (1)  
Visit Your Group * New Members 6  
 
• Privacy • Unsubscribe • Terms of Use
.

__,_._,___
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Poul Erik Karlshøj (PKA)-2]

I just installed KPA rev.1.38 and don't see any difference from 1.37. Both work very well here (with K3 4.83 and KAT 1.58). I will report if I find anything not working as expected.

KAT 1.58 removed a software bug in the KAT which meant that the KAT did not output anything on 28MHz when the KPA was OPR, but worked OK when the KPA was STBY (problem only on 28 MHz). The bug was suddenly triggered by something unknown (to me).

I am operating RC using Teamviewer, keying with Winkeyer and using KAT500-Remote and KPA500-Remote, both ver. 1.0.5.0. I am quite pleased with both. It is in fact possible to include everything (HRD (including logbook), WKey, KAT, KPA and other SW used for RC with iPad or iPhone) on a single laptop screen.

However, I have a few suggestions for improvements of the KAT500-Remote:
- The tune button should change colour (more clearly) when Tune is activated
- An indication should show "Power OFF" when the power of KAT is switched OFF
- The coloured fields for SWR should change colour following the SWR
- VFWD and VRFL could include peak values ( it is a nice-to-have feature, but the "living values" are essential when working remotely with weather sensitive antennas)

All in all I must say both programs are very useful even as they stand. Congratulations Elecraft.

73 de OZ4UN
Poul-Erik

> Den 18/02/2014 kl. 17.45 skrev "Wayne Burdick" <[hidden email]>:
>
> Hi all,
>
> We updated the KPA500 beta firmware to revision 1.38 yesterday (from 1.37). The change was minor, pertaining to initial conditions when the KPA500 is used at remote locations.
>
> If you get a chance, please load rev. 1.38 and verify that it is working well for all normal operation. Once we see a few more positive reports, we'll be going to production status on the K3, KPA500, and KAT500 beta firmware releases.
>
> If you haven't already loaded K3 rev 4.83 and KAT500 rev 1.58, I'd encourage you to do these updates as well. The difference between the new firmware and previous production releases is pretty dramatic, as reported by beta testers over the past several days.
>
> 73,
> Wayne
> N6KR
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[ke9uw]

I'm good with 1.38 also.