RE K2 Problem and new elecraft kit proposal

[KR4OW]

I believe the manual says not to remove the tape off
of the accesories that you are not using therfore
keeping the bugs and such out
David KR4OW
K2 4320


__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around
http://mail.yahoo.com 
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[f6dro]

OK abt the manual , but there are absoluty NO chance a tape can stop a mouse . I've just finished to clean the K2 , and after this , the problem is still there , so probably my problem is not mouse related. I'll check the control board more in depth later ( 8V and 5V are OK) . I suspect it is a controler problem , maybe the clock not starting reliably , more on this later
73 Dom/F6DRO

> Message du 23/10/07 14:18
> De : "David N."
> A : [hidden email]
> Copie à :
> Objet : [Elecraft] RE K2 Problem and new elecraft kit proposal
>
> I believe the manual says not to remove the tape off
> of the accesories that you are not using therfore
> keeping the bugs and such out
> David KR4OW
> K2 4320
>
>
> __________________________________________________
> Do You Yahoo!?
> Tired of spam? Yahoo! Mail has the best spam protection around
> http://mail.yahoo.com 
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
> http://mailman.qth.net/mailman/listinfo/elecraft 
>
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
>
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[bob conley]

Neither of the ones I've built had tape of the holes.
But, it does make sense to put tape over the blank
holes on the inside.

--- "David N." <[hidden email]> wrote:

> I believe the manual says not to remove the tape off
> of the accesories that you are not using therfore
> keeping the bugs and such out
> David KR4OW
> K2 4320
>
>
> __________________________________________________
> Do You Yahoo!?
> Tired of spam?  Yahoo! Mail has the best spam
> protection around
> http://mail.yahoo.com 
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
>  http://mailman.qth.net/mailman/listinfo/elecraft   
>
>
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
>

__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around
http://mail.yahoo.com 
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Mike Harris-9]

G'day,

I blanked off the battery switch hole on the QRP lid with a small piece of
PCB.  Shined it up and painted it with some clear nail varnish.  Looks
good.

Regards,

Mike VP8NO


----- Original Message -----
From: "Dominique DEHAYS" <[hidden email]>
To: "David N." <[hidden email]>; <[hidden email]>
Sent: Tuesday, October 23, 2007 9:25 AM
Subject: re: [Elecraft] RE K2 Problem and new elecraft kit proposal



OK abt the manual , but there are absoluty NO chance a tape can stop a
mouse . I've just finished to clean the K2 , and after this , the problem
is still there , so probably my problem is not mouse related. I'll check
the control board more in depth later ( 8V and 5V are OK) . I suspect it
is a controler problem , maybe the clock not starting reliably , more on
this later
73 Dom/F6DRO

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com