SSB Transmit Problems:K3

[pastormg]

Good Afternoon,
This is Mark Griffin, KB3Z. I just installed the KDVR and used config to turn it on and it did. But, for some reason when I key my microphone I am not getting any power output or ALC bars. I have it on transmit normal and the microphone gain has been turned up and down and no change. When I depress the XMIT/Tune button it gives me power output. Now, I realize that is a CW Signal. Also, when I use CW it works just fine. I don't understand why this is happening. It worked just fine before I installed the KDVR. I also tried disabling it via config and that didn't do any positive. Any suggestions, would be very much appreciated. Mark Griffin, KB3Z
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Jerry Moore]

Have you checked the owner's manual? Gain for the DVR can be set
differently. You didn't indicate which radio you have. But the K3S manual,
Page 30.
While speaking into the mic, adjust MON for
the desired level. (DVR playback level can be
set differently; see CONFIG:TX DVR).

-----Original Message-----
From: Elecraft [mailto:[hidden email]] On Behalf Of
[hidden email]
Sent: Friday, September 04, 2015 12:31 PM
To: [hidden email]
Subject: [Elecraft] SSB Transmit Problems:K3

Good Afternoon,
This is Mark Griffin, KB3Z. I just installed the KDVR and used config to
turn it on and it did. But, for some reason when I key my microphone I am
not getting any power output or ALC bars. I have it on transmit normal and
the microphone gain has been turned up and down and no change. When I
depress the XMIT/Tune button it gives me power output. Now, I realize that
is a CW Signal. Also, when I use CW it works just fine. I don't understand
why this is happening. It worked just fine before I installed the KDVR. I
also tried disabling it via config and that didn't do any positive. Any
suggestions, would be very much appreciated. Mark Griffin, KB3Z
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html Message
delivered to [hidden email]

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Jerry Moore]

And a details on page 31
 
Digital Voice Recorder (DVR)
With the KDVR3 installed, you can record and play
voice messages as well as capture received audio.
Transmit Message Record and Playback
Tap REC to start recording, then tap any of M1 -
M4 . Remaining buffer time will be displayed as
you speak. Tap REC again to end, or CLR to erase.
Tap M1 - M4 to play. To cancel, tap REC . If
you wish to manually assert PTT when using the
DVR, see CONFIG:KDVR3. MIC gain has no
effect during message play; the gain setting at
record time is used. However, DVR monitor level
can be set separately (see CONFIG:TX DVR).
To auto-repeat, hold (rather than tap) M1 - M4.
MAIN:MSG RPT sets the interval (1-255 seconds).
Hold REC to select bank 1 or 2 (4 messages each).

-----Original Message-----
From: Elecraft [mailto:[hidden email]] On Behalf Of
[hidden email]
Sent: Friday, September 04, 2015 12:31 PM
To: [hidden email]
Subject: [Elecraft] SSB Transmit Problems:K3

Good Afternoon,
This is Mark Griffin, KB3Z. I just installed the KDVR and used config to
turn it on and it did. But, for some reason when I key my microphone I am
not getting any power output or ALC bars. I have it on transmit normal and
the microphone gain has been turned up and down and no change. When I
depress the XMIT/Tune button it gives me power output. Now, I realize that
is a CW Signal. Also, when I use CW it works just fine. I don't understand
why this is happening. It worked just fine before I installed the KDVR. I
also tried disabling it via config and that didn't do any positive. Any
suggestions, would be very much appreciated. Mark Griffin, KB3Z
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html Message
delivered to [hidden email]

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[2M0TGN-2]

CONTENTS DELETED

The author has deleted this message.