Setting RS232 baudrate
Locked
 
|
HI ALL
Just installed version 4.05 in my K3 to run my P3 as well I always used the microkeyer at 4800 baud from the K3, but I'm not able anymore to set any other speed in the K3 as 38400. Yes I can change it, but the radio does not store it when I leave the menu. And I just can't get it to work on 38400, don't know why. So now my micro keyer is not reading the Radio any solutions? 73 de Dick PA3FQA ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
|
|
Dick, try this to set your speed to 4800:
Start the K3 Utility. On the Port tab, press "Test communications". The K3 Utility should find the radio at any of the supported speeds. Go to the command tester tab. Type "BR0;" (including the semicolon, but not the quotes) to choose 4800 bps. Go to the port tab and press "Test communications". Hopefully the radio will be at 4800 bps. Press the K3 power button to turn it off. During power-down, the K3 should write the current selected speed to EEPROM for the next power up. Press the K3 power button to turn it back on. Press "test communications". The radio should now be at 4800 bps. 73 de Dick, K6KR -----Original Message----- From: [hidden email] [mailto:[hidden email]] On Behalf Of Dick Grolleman Sent: Tuesday, September 14, 2010 6:11 AM To: [hidden email] Subject: [Elecraft] Setting RS232 baudrate HI ALL Just installed version 4.05 in my K3 to run my P3 as well I always used the microkeyer at 4800 baud from the K3, but I'm not able anymore to set any other speed in the K3 as 38400. Yes I can change it, but the radio does not store it when I leave the menu. And I just can't get it to work on 38400, don't know why. So now my micro keyer is not reading the Radio any solutions? 73 de Dick PA3FQA ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
Re: Setting RS232 baudrate
|
|
In reply to this post by Dick Grolleman
> So now my micro keyer is not reading the Radio > any solutions? The P3 forces the K3 to 38,400 bps whenever it is turned on. You set the baud rate for the P3 <-> computer (including the microKEYER) link using the "RS-232" menu item in the P3. Tap the P3 MENU button rotate the encoder until RS232 item is displayed tap the select knob rotate the encoder counter clockwise until 4,800 is displayed tap the select knob to select 4800 The alternative is to adjust microKEYER and your logging software to operate at 38,400 bps. 73, ... Joe, W4TV On 9/14/2010 9:11 AM, Dick Grolleman wrote: > HI ALL > > Just installed version 4.05 in my K3 to run my P3 as well > I always used the microkeyer at 4800 baud from the K3, but I'm not able anymore to set any other speed in the K3 as 38400. Yes I can change it, but the radio does not store it when I leave the menu. And I just can't get it to work on 38400, don't know why. > > So now my micro keyer is not reading the Radio > any solutions? > > 73 de Dick PA3FQA ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
|
|
In reply to this post by Dick Dievendorff
I didn't read your note carefully enough.
As W4TV correctly points out, the P3 to K3 speed is always 38400. The PC to P3 speed can be set to 4800 using the P3 front panel or the BR command. Dick, K6KR -----Original Message----- From: [hidden email] [mailto:[hidden email]] On Behalf Of Dick Dievendorff Sent: Tuesday, September 14, 2010 6:22 AM To: 'Dick Grolleman'; [hidden email] Subject: Re: [Elecraft] Setting RS232 baudrate Dick, try this to set your speed to 4800: Start the K3 Utility. On the Port tab, press "Test communications". The K3 Utility should find the radio at any of the supported speeds. Go to the command tester tab. Type "BR0;" (including the semicolon, but not the quotes) to choose 4800 bps. Go to the port tab and press "Test communications". Hopefully the radio will be at 4800 bps. Press the K3 power button to turn it off. During power-down, the K3 should write the current selected speed to EEPROM for the next power up. Press the K3 power button to turn it back on. Press "test communications". The radio should now be at 4800 bps. 73 de Dick, K6KR -----Original Message----- From: [hidden email] [mailto:[hidden email]] On Behalf Of Dick Grolleman Sent: Tuesday, September 14, 2010 6:11 AM To: [hidden email] Subject: [Elecraft] Setting RS232 baudrate HI ALL Just installed version 4.05 in my K3 to run my P3 as well I always used the microkeyer at 4800 baud from the K3, but I'm not able anymore to set any other speed in the K3 as 38400. Yes I can change it, but the radio does not store it when I leave the menu. And I just can't get it to work on 38400, don't know why. So now my micro keyer is not reading the Radio any solutions? 73 de Dick PA3FQA ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
|
|
Thanks Joe and Dick
All working agn 73 de Dick ----- Original Message ----- From: "Dick Dievendorff" <[hidden email]> To: "'Dick Dievendorff'" <[hidden email]>; "'Dick Grolleman'" <[hidden email]>; <[hidden email]> Sent: Tuesday, September 14, 2010 4:11 PM Subject: RE: [Elecraft] Setting RS232 baudrate >I didn't read your note carefully enough. > > As W4TV correctly points out, the P3 to K3 speed is always 38400. The PC > to > P3 speed can be set to 4800 using the P3 front panel or the BR command. > > Dick, K6KR > > > > -----Original Message----- > From: [hidden email] > [mailto:[hidden email]] On Behalf Of Dick Dievendorff > Sent: Tuesday, September 14, 2010 6:22 AM > To: 'Dick Grolleman'; [hidden email] > Subject: Re: [Elecraft] Setting RS232 baudrate > > Dick, try this to set your speed to 4800: > > Start the K3 Utility. > On the Port tab, press "Test communications". The K3 Utility should find > the radio at any of the supported speeds. > Go to the command tester tab. Type "BR0;" (including the semicolon, but > not > the quotes) to choose 4800 bps. > Go to the port tab and press "Test communications". Hopefully the radio > will > be at 4800 bps. > Press the K3 power button to turn it off. During power-down, the K3 > should > write the current selected speed to EEPROM for the next power up. > Press the K3 power button to turn it back on. Press "test > communications". > The radio should now be at 4800 bps. > > 73 de Dick, K6KR > > > > > -----Original Message----- > From: [hidden email] > [mailto:[hidden email]] On Behalf Of Dick Grolleman > Sent: Tuesday, September 14, 2010 6:11 AM > To: [hidden email] > Subject: [Elecraft] Setting RS232 baudrate > > HI ALL > > Just installed version 4.05 in my K3 to run my P3 as well > I always used the microkeyer at 4800 baud from the K3, but I'm not able > anymore to set any other speed in the K3 as 38400. Yes I can change it, > but > the radio does not store it when I leave the menu. And I just can't get it > to work on 38400, don't know why. > > So now my micro keyer is not reading the Radio > any solutions? > > 73 de Dick PA3FQA > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
|
|
In reply to this post by Dick Dievendorff
And, I'm sure the P3 communicates with the K3 for a reason. Why would you want to communicate at a lower speed, anyway? Dan -- N3ND -----Original Message----- From: Dick Dievendorff <[hidden email]> To: 'Dick Dievendorff' <[hidden email]>; 'Dick Grolleman' <[hidden email]>; [hidden email] Sent: Tue, Sep 14, 2010 10:11 am Subject: Re: [Elecraft] Setting RS232 baudrate I didn't read your note carefully enough. As W4TV correctly points out, the P3 to K3 speed is always 38400. The PC to P3 speed can be set to 4800 using the P3 front panel or the BR command. Dick, K6KR -----Original Message----- From: [hidden email] [mailto:[hidden email]] On Behalf Of Dick Dievendorff Sent: Tuesday, September 14, 2010 6:22 AM To: 'Dick Grolleman'; [hidden email] Subject: Re: [Elecraft] Setting RS232 baudrate Dick, try this to set your speed to 4800: Start the K3 Utility. On the Port tab, press "Test communications". The K3 Utility should find the radio at any of the supported speeds. Go to the command tester tab. Type "BR0;" (including the semicolon, but not the quotes) to choose 4800 bps. Go to the port tab and press "Test communications". Hopefully the radio will be at 4800 bps. Press the K3 power button to turn it off. During power-down, the K3 should write the current selected speed to EEPROM for the next power up. Press the K3 power button to turn it back on. Press "test communications". The radio should now be at 4800 bps. 73 de Dick, K6KR -----Original Message----- From: [hidden email] [mailto:[hidden email]] On Behalf Of Dick Grolleman Sent: Tuesday, September 14, 2010 6:11 AM To: [hidden email] Subject: [Elecraft] Setting RS232 baudrate HI ALL Just installed version 4.05 in my K3 to run my P3 as well I always used the microkeyer at 4800 baud from the K3, but I'm not able anymore to set any other speed in the K3 as 38400. Yes I can change it, but the radio does not store it when I leave the menu. And I just can't get it to work on 38400, don't know why. So now my micro keyer is not reading the Radio any solutions? 73 de Dick PA3FQA ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
«
Return to [K3]
|
1 view|%1 views
| Free forum by Nabble | Edit this page |