"Unmodules" for K2 web page?

[Ben Hofmann K1NT]

Does anyone know where I might find the information on
the "unmodules" for the K2.  The web page that they
pparently used to be on no longer exists, and my email
to the author is unanswered.

Thanks,

-Ben  KB1AHR
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft   
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Don Brown-4]

Hi

The unimodules were just male headers with jumpers that duplicate the Wx jumpers on the RF board. I made a set of them for troubleshooting a K2 radio. For example on the SSB module you need two three pin headers with pin 1 jumpered to pin 3 and a 12 pin with a .001 (102) cap from pin 7 to 12. These headers plug into the connectors on the RF board and allow the radio to work when the SSB module is removed. You can make other headers to go in place of the noise blanker, the 160 meter module, the 60 meter/xvertr module or the AF filter/DSP module. These are all just jumpers except the one for the noise blanker. In that case you need to build the 5 db attenuator onto the header rather than the jumper. Connect a 470 ohm resistor from pin 1 to pin 2 and another 470 ohm from pin 6 to pin 2. Then connect a 100 ohm resistor from pin 1 to pin 6. Install the resistors on the side of the header away from the SSB module so they do not interfere with the SSB module.

Don Brown


  ----- Original Message -----
  From: [hidden email]<mailto:[hidden email]>
  To: [hidden email]<mailto:[hidden email]>
  Sent: Saturday, October 02, 2004 11:14 AM
  Subject: [Elecraft] "Unmodules" for K2 web page?


  Does anyone know where I might find the information on
  the "unmodules" for the K2.  The web page that they
  pparently used to be on no longer exists, and my email
  to the author is unanswered.

  Thanks,

  -Ben  KB1AHR
  _______________________________________________
  Elecraft mailing list
  Post to: [hidden email]<mailto:[hidden email]>
  You must be a subscriber to post to the list.
  Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft<http://mailman.qth.net/mailman/listinfo/elecraft>    
  Help: http://mailman.qth.net/subscribers.htm<http://mailman.qth.net/subscribershtm>
  Elecraft web page: http://www.elecraft.com<http://www.elecraft.com/>
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft   
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Bob - W5BIG]

Hi Ben,

You can find a link to the original K2 un-module page at this url:

http://w5big.home.comcast.net

73/ Bob - W5BIG


----- Original Message -----
From: <[hidden email]>
To: <[hidden email]>
Sent: Saturday, October 02, 2004 11:14 AM
Subject: [Elecraft] "Unmodules" for K2 web page?

> Does anyone know where I might find the information on
> the "unmodules" for the K2.  The web page that they
> pparently used to be on no longer exists, and my email
> to the author is unanswered.
>
> Thanks,
>
> -Ben  KB1AHR
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):

http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
>


_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft   
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com