Yamaha CM-500 headset question

[Ron Manfredi]

In line with the replies about a good mic to use with the K3, I have a
question.  I am alternating between the Yamaha headset, (selected as the
rear mic, LOW output with bias) which works fine, and I would recommend
it .   However when I want to use the MH-3, I must not only change to
the front panel mic, but also change to No bias, and HIGH output.   Any
way to minimize the button selections that have to be made to do this?
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Ramon Tristani-2]

Just use a macro to select the microphone, port, and bias, output, etc. Easy.

> On Dec 5, 2016, at 10:42 PM, Ron Manfredi <[hidden email]> wrote:
>
> In line with the replies about a good mic to use with the K3, I have a question.  I am alternating between the Yamaha headset, (selected as the rear mic, LOW output with bias) which works fine, and I would recommend it .   However when I want to use the MH-3, I must not only change to the front panel mic, but also change to No bias, and HIGH output.   Any way to minimize the button selections that have to be made to do this?
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Don Wilhelm]

Ron,

I believe you meant the MH2 rather than the MH3 - the MH3 has a 1.8 inch
TRRS plug (for the KX3 and KX2) while the MH2 has the Foster plug that
mates with the K3/K3S front panel connector.

Secondly, the HIGH and LOW in the K3/K3S menu are NOT the output of the
mic, but instead Low mic gain and High mic gain.
The Low setting should work well with both the MH2 and the Yamaha.  Both
have electret elements, so the bias should be ON for both.
On other words, you should just have to switch from front panel mic to
rear panel mic.

You may have to make some slight adjustment to the mic gain when switching.

73,
Don W3FPR

On 12/5/2016 10:42 PM, Ron Manfredi wrote:

> In line with the replies about a good mic to use with the K3, I have a
> question.  I am alternating between the Yamaha headset, (selected as the
> rear mic, LOW output with bias) which works fine, and I would recommend
> it .   However when I want to use the MH-3, I must not only change to
> the front panel mic, but also change to No bias, and HIGH output.   Any
> way to minimize the button selections that have to be made to do this?
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]