static charges
Locked
 
|
Hello
I live at 3600 feet altitude on the Texas high plains where it is extremely dry, and we have a lot of wind. And lots of static eletricity. I have static charges jump as much as 3/4 of an inch to my hands daily, and usually several times a day. How can I protect my transceivers from this. I keep them grounded and the antennas disconnected when not being used. but sometimes I believe this attracks the static charges. I also keep them disconnected when not being used How can I protect the rigs from static??? ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
|
|
The first thing that comes to mind is a switch that would ground the
antennas when you disconnect them. Next thought is a path to ground when you are using them or not. That could be an RFC (Radio frequency choke) to ground or perhaps a resistor to bleed off the charge. Use of grounded antennas may be another possibility. That might be a loop antenna that is grounded at one end. Another could be a vertical with a matching network that provides a ground path. A description of the antennas that you have or intend to use would be useful to provide more specific suggestions! 73 - Mike WA8BXN ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
|
|
Hi Scott, I've drawn an arc from an 80m dipole at 30 feet on a dry sunny day, with the dry south wind blowing, that is over a half inch long... and it is repetitive. That is enough voltage and current to cook most any solid state device.. ... and will do damage if left to its own accord. What I get from my antennas now, that are 360 foot long and at 50 feet, is absolutely astounding, when observed in a dark room, from the open line feeders. What to do? Simple, and it works right easy too. Provide a straight... no.. really straight line to ground from the feedline. If you are using coax, then a gas tube discharge will work, and ground it with a very straight to ground path. No bends. And at the shack end, put a connector.. or coax T in the line, and solder a 1 meg resistor across the bottom of the T, from center to ground. That eliminates the static. Yes, you'll still need to disconnect when not using.. but it will allow you to use the antennas when the wind blows and the lightening isn't. Now for open lines.. it is even easier. when the line gets close to entry, take a gas tube discharge on each line.. and put the 1 meg resistor from each side of the feedline to the case or shell of the discharge. Keep them in a sheltered from rain case... that works well with a sealed like a Glad or Rubbermaid container.. with slits cut for the feedline to go through. Now you're safer from all the tracks of loose and unguided electrons that are of a mind for wanton distruction. good luck, and remember.. disconnect is always best.. IF it is a long ways away from anything else. --... ...-- Dale - WC7S in Wy ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
|
|
In reply to this post by Scott McDowell-3
CONTENTS DELETED
The author has deleted this message.
|
|
|
In reply to this post by Scott McDowell-3
Scott,
If you are referring to a static spark from your hand to the grounded equipment chassis, then I suggest purchasing a lot of "Static Guard" - that is the garment spray sold to eliminate static cling in clothing. Before touching the equipment, spray your chair, the carpet in the immediate vicinity and your clothing with the Static Guard. If you can eliminate any carpeting from the operating area, that will help a lot. Those static discharges will not usually harm equipment IF the equipment enclosure is metal and it is well grounded. The static charge should ideally flow to ground on the outside of the equipment enclosure - but then ideal conditions do not always exist, and your reasons for concern are valid. 73, Don W3FPR 73, Don W3FPR On 4/21/2011 10:41 PM, Scott McDowell wrote: > Hello > I live at 3600 feet altitude on the Texas high plains where it is extremely dry, > and > we have a lot of wind. And lots of static eletricity. I have static charges jump > as > much as 3/4 of an inch to my hands daily, and usually several times a day. > How can I protect my transceivers from this. I keep them grounded and the > antennas disconnected when not being used. but sometimes I believe this attracks > the static charges. I also keep them disconnected when not > being used > How can I protect the rigs from static??? > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
|
|
In reply to this post by AC7AC
Just received my K2 carry case Rose Kopp, ordered with two side pockets.
After reading such good reviews about her work I thought I'd take the plunge and order one. I am very pleased indeed with the product, fits my K2 perfectly and every thing else I need for my portable station. I have no connection with Rose other than a very satisfied customer! Info can be found on the Elecraft web site under "Other manufactures" 73 Roger MW0IDX Love the new KX3 but holding out for a KPA-500 K3 #191 K2 #2724 KX1 #416 ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html |
«
Return to [HAM]
|
1 view|%1 views
| Free forum by Nabble | Edit this page |