K3 Dead MCU Load
Locked
 
|
After using 2.57 for several months I decided to upgrade to latest
software. Started the K3 Utility, V 1.1.6.3 and had it check the website for upgrade. This is from the K3 Utility log: 13:31:24 K3 Utility Version 1.1.6.3 13:34:18 Opening connection to ftp.elecraft.com 13:34:18 Connected to Elecraft server. Please be patient, this takes a few seconds. 13:34:24 Copying files to C:\Documents and Settings\Owner\Application Data\Elecraft\K3 Firmware 13:34:31 Copied hmcu0278.hex from Elecraft 13:34:35 Copied HDSP0198.HEX from Elecraft 13:34:40 Copied HAUX0198.HEX from Elecraft 13:34:43 Copied hfwnotes.rtf from Elecraft 13:34:45 Copied K3UtilityVersionInfo.txt from Elecraft 13:34:45 Copied 5 files from Elecraft to C:\Documents and Settings\Owner\Application Data\Elecraft\K3 Firmware 13:34:45 Ready 13:37:28 K3 failed to enter MCU firmware load mode 13:37:36 MCU programming failed. Verify file source and version. Turn the K3 off and back on, then re-try the firmware load. 13:37:42 Ready 13:42:31 K3 is not responding 13:42:31 K3 is not responding 13:42:33 Ready 13:43:57 K3 is not responding 13:43:57 K3 is not responding 13:43:59 Ready 13:49:50 K3 is not responding 13:49:54 K3 is not responding I tried turning on and off the rig, of course by having to kill the power supply and holding the Power switch on until MCU LD reappears...along with flashing TX led. I am using the microKeyer II as my interface and went to the K3 port (3) and clicked on the "disable router inquiries" before starting the upgrade process. I did save the previous config using the K3 utility but now the K3 is not responding to the com port so K3 utility is essentially dead... Help! Tom _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
Tom,
Use a direect serial port connection or a USB to RS232 connection and it will pick up right where it left off. I could not update with my old MicroKeyer either so I hooked up a USB to RS232 and it updated the radio's firmware without a hitch. So, take the Microkeyer out when updating firmware to be safe. 73, Bob W5OV > After using 2.57 for several months I decided to upgrade to latest > software. Started the K3 Utility, V 1.1.6.3 and had it check the website > for upgrade. > This is from the K3 Utility log: > > 13:31:24 K3 Utility Version 1.1.6.3 > 13:34:18 Opening connection to ftp.elecraft.com > 13:34:18 Connected to Elecraft server. Please be patient, this takes a > few seconds. > 13:34:24 Copying files to C:\Documents and Settings\Owner\Application > Data\Elecraft\K3 Firmware > 13:34:31 Copied hmcu0278.hex from Elecraft > 13:34:35 Copied HDSP0198.HEX from Elecraft > 13:34:40 Copied HAUX0198.HEX from Elecraft > 13:34:43 Copied hfwnotes.rtf from Elecraft > 13:34:45 Copied K3UtilityVersionInfo.txt from Elecraft > 13:34:45 Copied 5 files from Elecraft to C:\Documents and > Settings\Owner\Application Data\Elecraft\K3 Firmware > 13:34:45 Ready > 13:37:28 K3 failed to enter MCU firmware load mode > 13:37:36 MCU programming failed. Verify file source and version. > Turn the K3 off and back on, then re-try the firmware load. > 13:37:42 Ready > 13:42:31 K3 is not responding > 13:42:31 K3 is not responding > 13:42:33 Ready > 13:43:57 K3 is not responding > 13:43:57 K3 is not responding > 13:43:59 Ready > 13:49:50 K3 is not responding > 13:49:54 K3 is not responding > > I tried turning on and off the rig, of course by having to kill the > power supply and holding the Power switch on until MCU LD > reappears...along with flashing TX led. > I am using the microKeyer II as my interface and went to the K3 port (3) > and clicked on the "disable router inquiries" before starting the > upgrade process. > I did save the previous config using the K3 utility but now the K3 is > not responding to the com port so K3 utility is essentially dead... > > Help! > Tom > _______________________________________________ > Elecraft mailing list > Post to: [hidden email] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
In reply to this post by CX7TT
Don't load K3 firmware through a microHAM device (actually the microHAM
router). It just doesn't work reliably. Dick, K6KR -----Original Message----- From: [hidden email] [mailto:[hidden email]] On Behalf Of TMorton Sent: Monday, January 26, 2009 7:57 AM To: [hidden email] Subject: [Elecraft] K3 Dead MCU Load After using 2.57 for several months I decided to upgrade to latest software. Started the K3 Utility, V 1.1.6.3 and had it check the website for upgrade. This is from the K3 Utility log: 13:31:24 K3 Utility Version 1.1.6.3 13:34:18 Opening connection to ftp.elecraft.com 13:34:18 Connected to Elecraft server. Please be patient, this takes a few seconds. 13:34:24 Copying files to C:\Documents and Settings\Owner\Application Data\Elecraft\K3 Firmware 13:34:31 Copied hmcu0278.hex from Elecraft 13:34:35 Copied HDSP0198.HEX from Elecraft 13:34:40 Copied HAUX0198.HEX from Elecraft 13:34:43 Copied hfwnotes.rtf from Elecraft 13:34:45 Copied K3UtilityVersionInfo.txt from Elecraft 13:34:45 Copied 5 files from Elecraft to C:\Documents and Settings\Owner\Application Data\Elecraft\K3 Firmware 13:34:45 Ready 13:37:28 K3 failed to enter MCU firmware load mode 13:37:36 MCU programming failed. Verify file source and version. Turn the K3 off and back on, then re-try the firmware load. 13:37:42 Ready 13:42:31 K3 is not responding 13:42:31 K3 is not responding 13:42:33 Ready 13:43:57 K3 is not responding 13:43:57 K3 is not responding 13:43:59 Ready 13:49:50 K3 is not responding 13:49:54 K3 is not responding I tried turning on and off the rig, of course by having to kill the power supply and holding the Power switch on until MCU LD reappears...along with flashing TX led. I am using the microKeyer II as my interface and went to the K3 port (3) and clicked on the "disable router inquiries" before starting the upgrade process. I did save the previous config using the K3 utility but now the K3 is not responding to the com port so K3 utility is essentially dead... Help! Tom _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
In reply to this post by CX7TT
Another thing you might try is to change the microHAM router so that the
radio type is "None". This is discussed (briefly) in the K3 Utility Help, Troubleshooting section under "USB to Serial Adapter Troubleshooting". It's the last item on that page. The microHAM router acts as if it's talking to a K3 that understands just the documented K3 command structure. The microHAM router doesn't faithfully pass through data sent to or from the PC program. The firmware load process uses data streams that are not part of the K3 command structure. The K3 doesn't understand the K3 command set until its MCU firmware is loaded. You'll have to get the microHAM router out of the way so that it doesn't attempt to manipulate the data being sent to or from the K3 during firmware load. The most straightforward way to do that is to cable the PC directly to the radio with an RS-232 serial cable or a USB to Serial Adapter that doesn't change the data stream. The microHAM router has provided an "escape" string that supposedly gets the router out of the way so that programs like the K3 Utility can load through the router. It doesn't work at this point. The router seems to be confused by the sequence of commands the K3 Utility sends as it attempts to determine the K3's baud rate and firmware inventory. I'll continue to pursue this (I own a microHAM device), but at this point in time it just doesn't work. Dick, K6KR -----Original Message----- From: [hidden email] [mailto:[hidden email]] On Behalf Of TMorton Sent: Monday, January 26, 2009 7:57 AM To: [hidden email] Subject: [Elecraft] K3 Dead MCU Load After using 2.57 for several months I decided to upgrade to latest software. Started the K3 Utility, V 1.1.6.3 and had it check the website for upgrade. This is from the K3 Utility log: 13:31:24 K3 Utility Version 1.1.6.3 13:34:18 Opening connection to ftp.elecraft.com 13:34:18 Connected to Elecraft server. Please be patient, this takes a few seconds. 13:34:24 Copying files to C:\Documents and Settings\Owner\Application Data\Elecraft\K3 Firmware 13:34:31 Copied hmcu0278.hex from Elecraft 13:34:35 Copied HDSP0198.HEX from Elecraft 13:34:40 Copied HAUX0198.HEX from Elecraft 13:34:43 Copied hfwnotes.rtf from Elecraft 13:34:45 Copied K3UtilityVersionInfo.txt from Elecraft 13:34:45 Copied 5 files from Elecraft to C:\Documents and Settings\Owner\Application Data\Elecraft\K3 Firmware 13:34:45 Ready 13:37:28 K3 failed to enter MCU firmware load mode 13:37:36 MCU programming failed. Verify file source and version. Turn the K3 off and back on, then re-try the firmware load. 13:37:42 Ready 13:42:31 K3 is not responding 13:42:31 K3 is not responding 13:42:33 Ready 13:43:57 K3 is not responding 13:43:57 K3 is not responding 13:43:59 Ready 13:49:50 K3 is not responding 13:49:54 K3 is not responding I tried turning on and off the rig, of course by having to kill the power supply and holding the Power switch on until MCU LD reappears...along with flashing TX led. I am using the microKeyer II as my interface and went to the K3 port (3) and clicked on the "disable router inquiries" before starting the upgrade process. I did save the previous config using the K3 utility but now the K3 is not responding to the com port so K3 utility is essentially dead... Help! Tom _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
In reply to this post by CX7TT
Every microHAM manual cautions against attempting to load firmware to a transceiver through Router and any of the microHAM interface hardware. The K3 is no different. In some cases, firmware can be uploaded if the K3 and Router are already communicating and Router is set to "Disable router queries" or if the radio type is changed to "no radio (mode selected manually)." However, in no case have I been able to salvage/resume a botched upload through Router and any microHAM interface. I keep a "real" serial port and/or a plain FTDI based USB to serial converter on my systems specifically for firmware uploads. 73, ... Joe, W4TV > -----Original Message----- > From: [hidden email] > [mailto:[hidden email]] On Behalf Of TMorton > Sent: Monday, January 26, 2009 10:57 AM > To: [hidden email] > Subject: [Elecraft] K3 Dead MCU Load > > > After using 2.57 for several months I decided to upgrade to latest > software. Started the K3 Utility, V 1.1.6.3 and had it check > the website > for upgrade. > This is from the K3 Utility log: > > 13:31:24 K3 Utility Version 1.1.6.3 > 13:34:18 Opening connection to ftp.elecraft.com > 13:34:18 Connected to Elecraft server. Please be patient, > this takes a > few seconds. > 13:34:24 Copying files to C:\Documents and Settings\Owner\Application > Data\Elecraft\K3 Firmware > 13:34:31 Copied hmcu0278.hex from Elecraft > 13:34:35 Copied HDSP0198.HEX from Elecraft > 13:34:40 Copied HAUX0198.HEX from Elecraft > 13:34:43 Copied hfwnotes.rtf from Elecraft > 13:34:45 Copied K3UtilityVersionInfo.txt from Elecraft > 13:34:45 Copied 5 files from Elecraft to C:\Documents and > Settings\Owner\Application Data\Elecraft\K3 Firmware > 13:34:45 Ready > 13:37:28 K3 failed to enter MCU firmware load mode > 13:37:36 MCU programming failed. Verify file source and > version. Turn the K3 off and back on, then re-try the > firmware load. 13:37:42 Ready 13:42:31 K3 is not responding > 13:42:31 K3 is not responding 13:42:33 Ready 13:43:57 K3 is > not responding 13:43:57 K3 is not responding 13:43:59 Ready > 13:49:50 K3 is not responding 13:49:54 K3 is not responding > > I tried turning on and off the rig, of course by having to kill the > power supply and holding the Power switch on until MCU LD > reappears...along with flashing TX led. > I am using the microKeyer II as my interface and went to the > K3 port (3) > and clicked on the "disable router inquiries" before starting the > upgrade process. > I did save the previous config using the K3 utility but now the K3 is > not responding to the com port so K3 utility is essentially dead... > > Help! > Tom _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
In reply to this post by Dick Dievendorff
I thought I saw the response that he got the firmware upgrade fixed by using
the new K3 Utility. He had not upgraded the K3 Utility. I have the MKII and am curious if it works successfully. The last upgrade I did, I was at a friend's station, and he used a serial cable to the firmware upload. John K8WDN -----Original Message----- From: [hidden email] [mailto:[hidden email]] On Behalf Of Dick Dievendorff Sent: Monday, January 26, 2009 1:20 PM To: 'TMorton'; [hidden email] Subject: Re: [Elecraft] K3 Dead MCU Load Another thing you might try is to change the microHAM router so that the radio type is "None". This is discussed (briefly) in the K3 Utility Help, Troubleshooting section under "USB to Serial Adapter Troubleshooting". It's the last item on that page. The microHAM router acts as if it's talking to a K3 that understands just the documented K3 command structure. The microHAM router doesn't faithfully pass through data sent to or from the PC program. The firmware load process uses data streams that are not part of the K3 command structure. The K3 doesn't understand the K3 command set until its MCU firmware is loaded. You'll have to get the microHAM router out of the way so that it doesn't attempt to manipulate the data being sent to or from the K3 during firmware load. The most straightforward way to do that is to cable the PC directly to the radio with an RS-232 serial cable or a USB to Serial Adapter that doesn't change the data stream. The microHAM router has provided an "escape" string that supposedly gets the router out of the way so that programs like the K3 Utility can load through the router. It doesn't work at this point. The router seems to be confused by the sequence of commands the K3 Utility sends as it attempts to determine the K3's baud rate and firmware inventory. I'll continue to pursue this (I own a microHAM device), but at this point in time it just doesn't work. Dick, K6KR -----Original Message----- From: [hidden email] [mailto:[hidden email]] On Behalf Of TMorton Sent: Monday, January 26, 2009 7:57 AM To: [hidden email] Subject: [Elecraft] K3 Dead MCU Load After using 2.57 for several months I decided to upgrade to latest software. Started the K3 Utility, V 1.1.6.3 and had it check the website for upgrade. This is from the K3 Utility log: 13:31:24 K3 Utility Version 1.1.6.3 13:34:18 Opening connection to ftp.elecraft.com 13:34:18 Connected to Elecraft server. Please be patient, this takes a few seconds. 13:34:24 Copying files to C:\Documents and Settings\Owner\Application Data\Elecraft\K3 Firmware 13:34:31 Copied hmcu0278.hex from Elecraft 13:34:35 Copied HDSP0198.HEX from Elecraft 13:34:40 Copied HAUX0198.HEX from Elecraft 13:34:43 Copied hfwnotes.rtf from Elecraft 13:34:45 Copied K3UtilityVersionInfo.txt from Elecraft 13:34:45 Copied 5 files from Elecraft to C:\Documents and Settings\Owner\Application Data\Elecraft\K3 Firmware 13:34:45 Ready 13:37:28 K3 failed to enter MCU firmware load mode 13:37:36 MCU programming failed. Verify file source and version. Turn the K3 off and back on, then re-try the firmware load. 13:37:42 Ready 13:42:31 K3 is not responding 13:42:31 K3 is not responding 13:42:33 Ready 13:43:57 K3 is not responding 13:43:57 K3 is not responding 13:43:59 Ready 13:49:50 K3 is not responding 13:49:54 K3 is not responding I tried turning on and off the rig, of course by having to kill the power supply and holding the Power switch on until MCU LD reappears...along with flashing TX led. I am using the microKeyer II as my interface and went to the K3 port (3) and clicked on the "disable router inquiries" before starting the upgrade process. I did save the previous config using the K3 utility but now the K3 is not responding to the com port so K3 utility is essentially dead... Help! Tom _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
«
Return to Elecraft
|
1 view|%1 views
| Free forum by Nabble | Edit this page |