Elecraft

Any message posted from one of the Sub-Forums below will show up in the section from which it is posted, and on the Elecraft mailing list. Messages posted directly from the email list will show up in the Main ("Topics") forum initially, but will eventually move to one of the sub-forums.

The Elecraft KX1, K1, K2 and K2/100 amateur radio kits capture the excitement of building and operating your own full-featured HF radio.

Or put together your own "K-Line" with the K3 transceiver, P3 Panadapter, and KPA500 solid-sate amplifier.

Order the new KX3 portable!

Elecraft: Hands-on-Radio (TM)

1 ... 851852853854855856857 ... 1823
Sub-Forums & Topics (63801)
Replies Last Post Views
Elecraft CW Net Announcement by kevinr@coho.net
0
by kevinr@coho.net
OT Yamaha cm500 by KV5J
1
by Jim McCook W6YA
Would like to experiment with hyperterminal to the k2 by dw-4
1
by Don Wilhelm-4
Mic Preamp for K2 by John R. Lonigro
3
by 'DGB'
CW power output and remote tuners by Kurt Bilinski
12
by Vic Rosenthal
45/75 Baud by Hank Garretson
0
by Hank Garretson
Transmitter performance by Dave-5
3
by Dave-5
Working Japan with a KX3 from Colorado by Gerry leary
2
by gregg.w6izt1
Fwd: K3/0 to K3 RemoteRig issue by Brian F. Wruble-2
19
by David Woolley (E.L)
Transmitter performance by Edward R Cole
0
by Edward R Cole
Re: [KX3] Re: filter for those with nearby AM broadcast stations by Ken G Kopp
6
by Jim Brown-10
FT-817 by Bruce Rattray
2
by Scotty Long
Configuration instructions by Ian Kahn, KM4IK
3
by Ian Kahn, KM4IK
JT9 by K5DNL
0
by K5DNL
K3 Macro Problem by Larry Boekeloo
1
by K9QJS
Re: Yamaha cm500 earpads by George M. Badger, II...
0
by George M. Badger, II...
K1 Power Out vs. Current Draw by Paul Kirley
0
by Paul Kirley
K-3 rig interface for N3FJP by gmuller885
4
by NZ0T
Re: Yamaha CM-500 (cushions) by Roy Koeppe
0
by Roy Koeppe
Where will Elecraft be showing near New England? by dw-4
5
by Eric Swartz - WA6HHQ
Re: K1 power out vs current draw. by Mike Morrow-3
0
by Mike Morrow-3
K3 and phasing & noise cancelling systems by Gary Smith-2
5
by Gary Smith-2
K-1 power out vs current draw. by k3hx@juno.com
2
by k6dgw
Re: K3, KX3 comparison by k6xt
0
by k6xt
tnx by Bruce Rattray
0
by Bruce Rattray
rtty via cw paddle by todd ruby-2
1
by jeff stai-2
k3 macro command for Speaker or Phones? by John Sweeney
5
by Edward R Cole
Re: Can there be a delay before xmit after pressing the XMIT button on my K3? by Edward R Cole
1
by Bob KD7YZ
Can there be a delay before xmit after pressing the XMIT button on my K3? by Bob KD7YZ
2
by Bob KD7YZ
OT Yamaha cm500 by KV5J
0
by KV5J
Elecraft K1 SN2761 on 160m QRV by Marc PE1FJN
0
by Marc PE1FJN
Configuration Questions by W1KSZ
4
by W1KSZ
K3/100 FS by k6xt
0
by k6xt
Run Run Rudolph by mikerodgerske5gbc
1
by Gary Smith-2
K2 inductor wattage by John Cooper
1
by Don Wilhelm-4
1 ... 851852853854855856857 ... 1823