Elecraft

Any message posted from one of the Sub-Forums below will show up in the section from which it is posted, and on the Elecraft mailing list. Messages posted directly from the email list will show up in the Main ("Topics") forum initially, but will eventually move to one of the sub-forums.

The Elecraft KX1, K1, K2 and K2/100 amateur radio kits capture the excitement of building and operating your own full-featured HF radio.

Or put together your own "K-Line" with the K3 transceiver, P3 Panadapter, and KPA500 solid-sate amplifier.

Order the new KX3 portable!

Elecraft: Hands-on-Radio (TM)

1 ... 1601160216031604160516061607 ... 2698
Topics (94418)
Replies Last Post Views Sub Forum
S Merter Lite 2.21 now supports the K3 by NZ0T
5
by NZ0T
[K3]
K2 Alignment with Signal Generator? by Jim Stephens
1
by Don Wilhelm-4
[K2]
KPA500 Cables -- Needed for K3 ?? by Phil Hystad-3
5
by Dick Dievendorff
[QRO]
K3 Wanted by Julius Fazekas n2wn
0
by Julius Fazekas n2wn
[K3]
Thanks to all who replied - KPA500 - 500W out on 120VAC? by vtnn43e
0
by vtnn43e
[QRO]
N2CQ QRP Contest Calendar: Aug 10 - Sep 10, 2011 by Ken Newman-2
0
by Ken Newman-2
[HAM]
[K3] Audio cutting out?? by K2QI
6
by Mike Reublin
[K3]
K3 memory by David Windisch
3
by Pierfrancesco Caci
[K3]
Huntsville Hamfest -- Elecraft Booth Support & Monte Sano QRP Event by CRAIG W BEHRENS
0
by CRAIG W BEHRENS
Test -- Just Joint the List by CRAIG W BEHRENS
0
by CRAIG W BEHRENS
[OT]
HELP! K3 dead by WD6DBM
2
by WD6DBM
[K3]
KAT500 and KPA500 by Arie Kleingeld PA3A-...
13
by w0mu
[QRO]
KPA500 - 500W out on 120VAC? by vtnn43e
5
by w7aqk
[QRO]
KPA - 500 # 292 by Paul VanOveren-2
0
by Paul VanOveren-2
[QRO]
K3: Firmware 4.39 by DL5OCD
4
by DL5OCD
[K3]
[K2] NB2 heard a "spark gap" like signal 8k lower than the RX frequency by Wayne Conrad
4
by Wayne Conrad
[K2]
K3 Transmit ALC characteristics by Torrey Mitchell
5
by Cady, Fred
[K3]
New DXCC ST0R, Southern Sudan by Paul VanOveren-2
5
by Tony Estep
[HAM]
K2's DSP? by Steve_wGØAT
2
by Arie Kleingeld PA3A-...
[K2]
PL1 err by WA8EBM
0
by WA8EBM
[K3]
K144XV output power range by Stan Gibbs, KR7C
4
by Stan Gibbs, KR7C
[K3]
K3 RTTY with a paddle by w0mu
1
by Nels Anderson
[K3]
[K3] ERR PL1 has shown up by Tom Boucher
0
by Tom Boucher
[K3]
KPA500 10 meter behavior by K5SM
6
by Don Wilhelm-4
[QRO]
Hope the K2 is still around once the KX3 is released by Don Baucom
0
by Don Baucom
[K2]
FOR SALE: ELECRAFT K2/100 by Donald, K6RV
1
by Donald, K6RV
[K2]
KAT2 J8 by EMD
2
by EMD
[K2]
AGC shuts off by itself by tomb18
1
by Don Wilhelm-4
[K3]
[P3] P3 and K144XV by N5GE
9
by Tom Azlin N4ZPT-2
[P3]
FW: [cwops] Another youngster on CW by Chester Alderman
1
by Chester Alderman
[HAM]
OBITUARY -- TOM HAMMOND, N0SS by KENT TRIMBLE
0
by KENT TRIMBLE
K3 non pc rtty setup by Smith Bradford
0
by Smith Bradford
[K3]
KPA500 by Phil LaMarche-2
1
by AC7AC
[QRO]
P3 Span Control by W7CS
0
by W7CS
[P3]
K3/100 For Sale by Larry Boekeloo
0
by Larry Boekeloo
[K3]
1 ... 1601160216031604160516061607 ... 2698